How to assemble the trimmer strap
Balancing the handles
Finding the correct position of the handles for easy work with the lawn mower. For ease of adjustment, it is advisable to find a model with separate adjustment of the handles. In these models, the handle is fixed with four screws. By unscrewing the top screws, you can adjust the angle of rotation of the handles. By removing the bottom screws, you can adjust the handle to your height.
Some lawnmower models are equipped with twin handles that do not have an adjustable angle of rotation. In order for the handles not to rest against your feet when working with such braids, they must be lowered on the working shaft. When the handles are lowered, the lawn mower has to bend over or lift, so the back or arms get tired during prolonged work.
How to properly cut grass with a trimmer?
The first step is to adjust the trimmer belt so that the drum is not touching the ground. Further, it is important to remember that due to the thick line there will be an overload of the trimmer, so do not overdo it with the thickness.
You should not wind a lot of fishing line on the drum.
Remember to clean your trimmer periodically.
Be sure to lubricate the cable.
The trimmer is very handy as it can be used in a wide variety of places, including difficult terrain and areas near trees. If you are cutting tall grass, start with the raised tops first and then continue with the bulk.
The main thing is to correctly adjust the trimmer belt so that the drum with the line does not crawl along the ground.
Make the right gasoline-oil mixture.
Do not use a line that is too thick. it picks up speed and overloads the trimmer.
Do not be afraid to give it revs.
How To Install A Universal Trimmer Strap
Do not wrap too much line on the drum, and do not wind it too much.
Stop and clean the “basket” from time to time.
Lubricate the trimmer cable and the gear train (if any) with grease.
Before mowing the grass, first, adjust the line and secure it well in your cavity so that the line does not hang out and does not go here and there. Next, fill in the fuel accordingly (if you do not have an electric trimmer), which consists of special oil and gasoline. Next, start mowing the grass with smooth movements (not fast) to the right and left. Do not try to chop off the thick stems of plants often, as the line will instantly run out and you will have to tune the reel again. In dense places, the main thing is not to spare the gas)
The technique of mowing grass with a trimmer is not very complicated and takes into account the need for:
- decide exactly how you are going to mow. Can be folded, can be across.
- choose a place so that a bald patch does not appear as a result and the site looks harmonious
- understand what exactly you are going to mow, and depending on the choice, put the right knife. They are different. For example, hay or weed. You also need to set the speed.
- of course, it is necessary to prepare both clothing and protective equipment. No matter how experienced you are, you must wear glasses. and not forgetting headphones and long clothes.
All the details of the technique are on the video how to mow with a trimmer.
Use the trimmer as directed. The electric scythe (that is, the trimmer) is good because it does its job well in hard-to-reach places. Therefore, the trimmer can be used near trees, fences in relief areas. And not only for mowing the lawn, but also for ordinary grass.
The main thing is to make sure that the weeds do not have time to give seeds and mow them on time.
If you did not have time to mow the grass before the moment it gave the ears, then first mow the tops of the spikelets and burn them. And only then mow the grass itself, and put it in compost.
Trimmer from the Varyag company koshu according to the instructions:
Step 1. Installing the cutting device.
Depending on the type of weed, we choose a cutting tool: a fishing line for soft-stemmed grasses, a knife for hard-stemmed and small shrubs. We unscrew the nut of the cutting mechanism and install the cutting tool. Tighten the nut, the mechanism is ready to work.
Note: some trimmers do not have interchangeable cutting tools, so you can start using them right away.
Step 2. Preparing the trimmer for work.
If the trimmer is electric, we charge the battery or turn on the motor to the network. If the petrol tank is filled with fuel. Then, depending on the type of trimmer, we adapt it to ourselves (the upper motor is hung with a loop on the shoulder, the knapsack is by the shoulders, the lower upper arm is grabbed by the handles). Hold the trimmer over the grass so that its cutting mechanism is parallel to the area to be treated. We start the engine.
Step 3. Mowing.
The grass trimmer is mowing with simple movements. It is important to remember that the cutter bar of the device rotates counterclockwise so that the cut grass will fall onto the already worked area. The first is from right to left in front of us (this is how we cut off the top of the grass). Second from left to right (this is how we remove the remnants of the grass).
It is better to divide a large area of the cultivated area into squares, and mow the grass on them, moving from one to the other along the outer side of each square.
When mowing grass on slopes, it is recommended to mow from below, moving parallel to the sloping area. We reached the edge, returned back, became a little higher and repeat the same route until the site is completely mowed.
To mow grass in an area where there are trees, it is better to use a forestry cutting mechanism, and you need to mow, passing the area around the perimeter, bypassing the tree around the trunk.
Step 4. Finish work.
After the end of the mowing of all the grass on the site, turn off the engine, remove the trimmer (for shoulder and backpack devices), clean the cutting mechanism of grass residues.
If you decide to cut the grass with a trimmer, it is important not only to carefully prepare for the cutting process. It is also important to be good with the trimmer and have a protective suit. In addition, it is necessary to be able to adjust the trimmer.
colleagues who regularly and heavily use petrol trimmers, tell me how to choose the right shoulder strap length and handle position.
Before that, I had an electric, lightweight, mowed and not steamed. One problem, the wire had to be constantly monitored so as not to accidentally “mow” it. This year, the electric gearbox is jammed. Took a simple petrol Chinese. (if anyone is interested. patriot 3045). With J-handle. I started to mow. I was tired halfway through the plot. Both hands are constantly tense. The right one gets more tired, because still have to put pressure on the gas. If I make the belt shorter, then I cannot cut the grass short. And it turns out that I generally hold the trimmer in my hands. The belt only saves from jerks (when you accidentally hook the ground, and the trimmer tries to run away). Twisted. To everyone. I just can’t find it to be convenient. In general, share a trick on how to properly adjust the length of the strap and the position of the handle.
Nothing will help you. This is a trimmer. unergonomic, designed for short work. I’ve tried about five different ones. The trimmers of the lower linear row also have the disadvantages that you described. I concluded that the most convenient to use is a lawn mower with a straight bar (shaft inside) and with horn handles. That’s where the weight distribution is at a height, and the vibration in the palm of your hand is acceptable, and the mowing area is larger. But even from such a braid, the next day, the shoulder hurts from the belt, and I began to notice that the knee joint of the left leg begins to hurt from the constant rotational movement on this leg. And you have to mow a lot. Or one day from morning to evening, but it is better 2 times for half a day. Spit and health is easier. This year, on the advice of Vadim, I bought a Bosch ARM 34 trolley. I’m happy as an elephant.
I am learning to insert images correctly. I didn’t understand only one thing. where does the width of the picture look (800 px). I climbed everything in Yandex, but did not find the parameters.
You just need to look for the center of gravity of the braid. I use an interskolovsky brush cutter, where the belt was initially attached in the wrong place, the overweight was in one direction, I had to hold it with my hands. I found the center of gravity, weighed the belt there, adjusted the length and that’s it. The weight is now on my shoulder, I only control my hands.
The comfort of the gardener and, as a result, the speed and duration of his work depends on the correct fastening of the lawn mowers on the backpack belt. Many people do not want to spend time adjusting the petrol trimmer mounts on a two-shoulder strap, and perhaps this is justified if it is necessary to mow down the grass only in a small area or near a fence, but in large areas, the issue of convenience and endurance will become paramount if we do not want to stretch the mowing for several days. In addition, a properly adjusted lawn mower mount will make mowing much safer. As for me, it is worth understanding this issue.
Electrokosa
With an electric trimmer, everything is much easier. After making sure that the gearbox has the required amount of lithol, you can start working. No additional measures are required. Unless it is necessary to ensure that the carrier does not run in the path of the mowing in order to avoid possible damage.
When the device itself is ready for use, you should make sure that there is nothing around that could interfere with the operation. If possible, the intended area of mowing should be cleared of driftwood, glass, stones and other solid objects that could damage the knife or line.
It is better if other people do not approach the trimmer during operation. Usually the recommended distance is at least 10-15 meters in order to avoid getting small debris (mulch) in the eyes and on the face.
Depending on the work to be done, you need to choose a trimmer attachment: a screw-knife for weeds and hay, a line for lawn grass or a circular saw for shrubs. Mowing should be in the opposite direction from people, if possible, then moving away from buildings and buildings. Do not get too close to the fence and other structures, as the fishing line can catch on sharp edges, and the screw-knife bend if accidentally hitting a hard object with it.
The preparation of the device itself does not take much time, all modern models of devices are designed in such a way as to facilitate and simplify their operation, starting to work as soon as possible.
Getting ready for operation
As with any technique, there are rules for working with a trimmer. First you need to make sure that the main components and assemblies are intact: the screw, rod, handle and motor. If the device has not yet been assembled, then it should be properly assembled according to the instructions.
Position of the lawn mower in relation to the belt
The lawnmower must be properly secured to the belt. In order for the garden tool not to rise up during work, and it was convenient to mow the grass, the belt is fixed at the back of the handle. If the belt is fastened too close to a full fuel tank, the gas scythe will go deeper into the ground and the cutting elements will bite into the soil. No cutting element is designed to be in contact with the ground. If the mowers are in the wrong position, the cutting elements quickly become dull. To extend the life of the cutting elements, gardeners raise the mower. With such work, the back gets tired quickly.
The petrol braid should hang freely on the belt. For proper balancing, fasten the strap so that the full fuel tank and the mower are balanced. It is also important to find such a position of the gasoline streamer, when working in which you will not close the exhaust port of the engine, otherwise the engine will overheat during long-term operation.
how to properly adjust the trimmer belt
IMPORTANT! To bookmark the article, press: CTRL D
You can ask the DOCTOR a question and get a FREE ANSWER by filling out a special form on OUR WEBSITE, by this link
A lawn mower is a handy tool for mowing lawns or tall grass when properly balanced. It’s not about balancing the line or knives. You need to balance the operating handle, as well as the position of the gasoline scythe on the belt. Many gardeners do not use a belt when working with a gasoline scythe, so their arms and back get tired. A support strap must be used for comfortable operation. These belts are supplied with professional gasoline braids. For Chinese petrol braids, the support belt needs to be purchased additionally.
Adjusting the lawn mowers attachment. What to strive for.
Once the two-handed handle and backpack-style strap have been adjusted, the cutter of the lawn mower hanging on the harness should be parallel to the ground, without your hands touching the garden tool. The height, of course, can vary depending on the task being performed, 20-30 centimeters when mowing tall grass for forage, 5-10 centimeters for mowing lawn grass.
The lawnmower must be balanced with the cutting tool installed: a disc or a spool of line.
Adjustment: backpack strap / backpack strap / backpack strap / shoulder strap / parachute strap.
Perhaps due to inaccuracies in translation, now you can find many names for belt suspension of garden equipment: knapsack belt / backpack belt / backpack-type belt / shoulder belt / parachute belt. For lawn mowers, only a two-shoulder strap is suitable, hence the association with a backpack and a knapsack, which must be correctly attached and fitted to the figure. You can, of course, hang it on one harness, a belt loop, but I do not recommend it, except for very low-power models. Weight and vibration will quickly make themselves felt.
The first step is to adjust the height of the double-shoulder harness hook to suit your height. To do this, we put on the backpack strap and tighten the shoulder straps so that the hook is palm-width below the hips, and the load is evenly distributed over the straps. If you pull the trimmer higher, it will only narrow the grip of the grass, and the cutter will most likely be at an angle to the ground.
We hang the lawn mower. By moving the hook to the desired hole in the bar, we balance the petrol trimmer so that the knife, when the hands are released, is at the height selected, depending on the tasks.
On those lawn mower models that are equipped with an attachment loop, not a bar, you need to balance it by moving it along the bar.
The purpose of this balancing is to distribute the weight of the gardening tool through the backpack-style belt to the shoulders, rather than constantly supporting it with your hands. Hands should only give direction to the cutting tool.
Then you need to adjust the two-handed handle of the petrol trimmer. If the balancing of the garden tool is then disturbed, then it is necessary to repeat all the steps until the result is achieved.
It is not always possible to get the perfect balance between lawn mowers on a backpack strap. Sometimes the parallelism of the knife to the ground can be achieved only with a personal selection of the length and replacement of the standard trimmer bar. Do not forget that the amount of fuel in the tank of motor vehicles will also affect the center of gravity. But even an imperfect adjustment of the lawn mower mounting can greatly facilitate the work of the operator.
In every summer cottage, village, suburb and in the city itself, you can see these devices: they work tirelessly, leveling the lawn grass, clearing the space of squares and parks, gardens and vegetable gardens from thickets of burdock, wormwood and weeds. The noise and crackling noise of the trimmers can be heard from early summer to autumn, until the growth of the grass slows down enough that it is no longer necessary to trim it. The automatic scythe has earned its popularity for its simplicity of design and operation. It is easy to use, easy to care for, and in the event of a breakdown it cannot be easily repaired. The article will just tell you how to use the grass trimmer correctly.
Fastening the shoulder strap
One of the simplest manipulations when assembling a trimmer. Many will understand how the shoulder strap attaches intuitively. For those who are not sure, we decided to add several important points to the instructions:
We connect the carabiner with the ring for fastening the belt
2. Adjust the position of the mounting ring on the rod
3. We fix the ring with the fixing screw
Assembling the trimmer step by step
How to assemble a trimmer. Step by step instructions PHOTO VIDEO
Garden trimmers are similar in design. Detailed instructions for one model will help you understand the intricacies of installing analogs. Consider the main stages of assembling a trimmer using a model as an example. FUBAG FET 1200R.
Before we start, let’s figure out what we have in our hands after the purchase. The tool is sold disassembled:
- Boom with motor
- Braid handle
- Trimmer head cover
- Trimmer head
Also included is a shoulder strap, a three-blade knife and a tool kit.
We fix the tool handle
Unscrew the thumbscrew
2. Remove the top cover of the fastener
Insert the handle into the fasteners
Installing the cover
Tighten the screw
To adjust the handle, you need to loosen the thumbs and move it. Then fix the screw.
trimmers FUBAG equipped with rubberized handles, which increases the convenience and safety of use. They allow you to hold the tool securely even in wet hands.
Installing the protective cover
We combine the holes in the protective casing and in the fastening bar.
We fix the cover on the bar with screws and washers using the key from the kit.
In this model, the casing is fixed with metal plates on both sides. This guarantees additional reliability and durability of the trimmer.
The casing itself is made of dense but elastic plastic. Such material will definitely not break off when hitting small obstacles. We advise you to pay attention to this if you are just going to choose electric trimmer or petrol trimmer.
Installing the line reel
To begin with, we combine the hole on the washer with the hole in the gearbox cup and lock it with a special rod.
We unscrew the fastening nut from the hub clockwise.
3. Remove the cup from the shaft and the pressure washer
Important! We leave the flange washer.
We twist the spool of line counterclockwise until it stops, holding the rod.
How to Replace the Trimmer Starter Cord
How to repair a trimmer starter
Petrol trimmer starter repair may be required at the most inopportune moment. With all this, the problem can be solved by 2 methods: replace a broken part or change the entire unit. The latter option is more expensive. To repair the device with your own hands, in most cases, you will only need a screwdriver with a suitable tip from the tools.
how to replace the starter cord on the trimmer. Starter repair let us wind the cord on How to draw on. Repair work does not take much time and does not require special knowledge. How to replace the trimmer line. How to replace the cord and Replacing the starter cord with.
It is enough to know the device, the mechanism of operation, aspects of assembling and disassembling the starter on the trimmer in order to achieve a suitable good result.
How to Coil the Trimmer Starter Spring
The starter cable does not reel: how to find out the cause and repair the starter with your own hands? How to disassemble the starter, stick in and pull the spring yourself again
Dismantling, disassembly of the trimmer starter, replacement of parts
First of all, the repair process begins with removing the entire starter from the trimmer.
This process is inherently not complicated and will only require unscrewing a few screws with a suitable locksmith tool.
It should be noted that safety precautions must be observed when dismantling the lawn mowers starting mechanism, since the ribbon spring in the compressed state has enough energy to injure a person.
Installing or replacing the starter spring for lawn mowers, motor-drill, trimmer
But what if everything is in perfect order with the rope, and the reel (pulley) of the starter does not unwind? Let’s take a look at this question step by step using the example of the starter of the gasoline ADA GroundDrill motor-drill, which has a pulley with 2 metal antennae for 2 hooks.
In the case of other types of manual starters of an identical design, which are widely used in gasoline lawn mowers, trimmers and motor drills, the whole process of repairing a starter will look the same, differing only in certain aspects.
Diagnostics
Diagnostics of the tool triggering system is carried out as follows:
Spring tension
After installing the spring, tighten it. To do this, do the following actions:
- remove the handle from the starter cord;
- then the rope is inserted into the reel groove;
- create tension on the spring by rotating the coil in the opposite direction to the clockwise movement (winding);
- make the required number of revolutions indicated in the instruction manual for the trimmer used and corresponding to the length of the cord used;
- at the very end, the rope is threaded into the hole created for this, located in the starter cover;
- put the handle in place, fixing it with a knot.
If, after repair, the spring continues to fly off, then you can get rid of it in the following ways:
- squeeze a piece of the plate suitable in size into the groove at the location of the spring hook;
- drill holes on both sides of the groove in the spool, into which to insert the spring hook and fix it with a wire.
Spring tension
After installing the spring, tighten it. To do this, perform the following actions:
- remove the handle from the starter cord;
- then the rope is inserted into the reel groove;
- tension the spring by rotating the coil in the opposite direction to the clockwise direction (winding);
- make the required number of revolutions specified in the operating instructions for the used trimmer model and corresponding to the length of the cord used;
- at the very end, the rope is threaded into the hole intended for this, located in the starter cover;
- put the handle in place, fixing it with a knot.
If, after repair, the spring continues to fly off, then you can get rid of it in the following ways:
- squeeze a piece of the plate suitable in size into the groove at the location of the spring hook;
- drill holes on both sides of the groove in the spool, into which to insert the spring hook and fix it with a wire.