Reciprocating saw with your own hands from an electric screwdriver

The man is in the kitchen. it is strong!

Did you know that an electric screwdriver can do much more than you expected? Of course, its true purpose is to drill holes and tighten fasteners. But the most creative owners have come up with a whole list of other uses for this device.

A real man not only perfectly owns both of these devices, but can also make one of the other. In this case, the time spent will be no more than five minutes. There are some tips.

All that is required for such a “modernization”. remove the drill chuck and insert the whisk from the mixer into the vacant socket. If the whisk is not at hand, an ordinary fork will help out.

This rework will be a real salvation when the knives of your meat grinder are hopelessly dull. So, to create an electric meat grinder from an electric screwdriver, you will need:

• old manual meat grinder;
• electric screwdriver;
• metal bolt without a head with a hexagonal top.

Next, you just need to get the shaft out of the old meat grinder and insert it into the electric screwdriver along with the screw. As a result, you will get a really powerful high-speed unit.

Universal tool

An ordinary electric screwdriver will become a real godsend not only when performing your direct duties. drilling holes and tightening fasteners, but for many other tasks. Let’s take a closer look at some of them.

Sharpening knives with an electric screwdriver

How to sharpen a knife if there is no familiar bar and show the class? In this case, you can improvise and use a conventional electric drill. To sharpen a knife with an electric screwdriver, you also need a glue gun and sandpaper.

• cut a small strip of sandpaper and attach it to the drill sleeve with a glue gun;
• put the electric screwdriver on a flat surface and fix it with a vise;
• turn on the tool at minimum speed and run several times with the side of the knife on the sandpaper;
• turn the knife over and slide it over the rotating sleeve a few more times.

Drill attachment for grinding

Construction work often requires specialized tools. But in the case of rare use, the acquisition of unnecessary devices is unprofitable. In this case, your electric screwdriver will again become a faithful assistant, or rather, special attachments for a drill, expanding the capabilities of this tool.

The most popular is the grinding attachment for the drill. With its help, you can perform a wide range of related work.

According to the shape, the following types of grinding attachments are distinguished:

• cup. to remove old coating and corrosion;
• disk and plate. differ from the cup by the direction of the bristles. They have Velcro, which allow you to fix the abrasive material on them. The most convenient are plate nozzles, since they allow you to adjust the angle of inclination and follow the contours of the product;
• petal. with their help you can handle holes and hard-to-reach places, since the product can take any shape;
• end. for working with glass, metal and wood.

We cut metal with an electric screwdriver

No matter how it sounds, you can cut metal with an electric screwdriver. For this, a special scissor attachment is used for cutting metal. The advantages of using such a nozzle over manual scissors are:

• minimum cutting radius;
• the possibility of obtaining round holes;
• high-quality edge that does not require further processing;
• elimination of deformations;
• saving.

The disadvantages in this case are noise during operation, limitation on the thickness of the processed materials, difficulty in performing an even cut.

In general, such a cricket nozzle will be the best solution for a home craftsman.

ways of non-standard use of an electric screwdriver at home

The cordless electric screwdriver really is almost the main tool in every home. With its help, tasks are performed around the house, in the garden, in the garage, etc. It is also much more convenient than network models, since it does not require constant connection to the mains. In this case, the “charge-discharge” cycle is not eternal, whatever the rating of the device.

Safety engineering

When performing any work with an electric screwdriver, do not ignore the safety precautions:

Disassembly Cheap Cordless Reciprocating Saw. How It Work. Best Value 2020

• to avoid electric shock, do not touch grounded objects while the tool is running;
• check the drilling sites for hidden wiring;
• do not touch the rotating parts of the tool and do not try to stop them manually;
• connect the tool only to a network with a suitable voltage;
• do not turn on the tool until it comes into contact with the material;
• immediately before work, make sure the workpiece is motionless;
• do not wear loose clothing or jewelry before work. they can get caught in the moving parts of the tool.

Remember that following simple safety rules will save not only your health, but also your life.

Do it yourself: a reciprocating saw based on an electric screwdriver

The idea of ​​making a homemade reciprocating saw belongs to the author Hassan Abu-Izmero.

Homemade product from the category “it was in the evening. there was nothing to do,”. And yet, perhaps someone will be interested in this design.

Although we called the homemade saber saw (for its external resemblance), by and large, it is still more of a jigsaw. The files for this homemade product are used precisely from him.

We recommend that you read the article: how to make a convenient stand-holder for sawing logs.

The peculiarity of the home-made design is that with this saw you can make both straight and curly cuts (only the file will need to be installed appropriately).

The main stages of work

First of all, the author makes the main part of the homemade product. a reciprocating mechanism.

Next, you will need to make a case in which this mechanism will be located. The author uses a piece of a profile pipe for this.

In one of the round bars, the master makes a slot for the file. this will be the file holder. The second bar will be inserted into the chuck of a drill or electric screwdriver.

You will also need to make a file holder. The author uses a nut for this. you need to drill a hole in it for the fixing screw. The nut itself will need to be welded to the file holder.

A guide for the file must be made from a metal plate, and a fastener for it is made from pieces of metal.

At the last stage, it remains only to clean the body with an angle grinder or on a grinding machine, and paint the homemade product.

The process of making a reciprocating saw can be seen in the video below. How do you like this idea? Share your opinion in the Комментарии и мнения владельцев.

Drill Description

The drill is a hand-held electric machine in the shape of a pistol. Designed for making holes in wood, metal (steel), plastic, brick and (reinforced concrete) concrete. It is used in construction and renovation. at the industrial and domestic level as preliminary installation work. Modern devices, in addition to performing direct functions, “perform” the work of a grinder, angle grinder, mixer, mains or cordless electric screwdriver. Unit design:

• plastic (or aluminum) case with rubberized handle and additional handle;
• collector motor with stator, rotor, armature and brushes;
• keyless chuck fixing the nozzle (drill);
• start button: fixedly snaps into place during long-term operation;
• speed regulator: adjustable depending on the processing material;
• cord with a plug for connecting to the mains;
• metal stop rod: controls the drilling depth;
• diode illumination of the place of work.

Drilling begins with setting the depth gauge and setting the speed: the harder the product, the lower the revolutions should be. The handle is gripped and the “start” button is pressed: the direction of the rig must be along the axis of the hole in perspective. Through the spindle, the rotation is transmitted to the gearbox, as a result, the drill is driven into a bar, corner, reinforced concrete foundation. The work is carried out technically carefully, because, for example, a Bosch drill or an Interskol drill develop a speed of ≈ 1300 rpm. plus / minus depending on the model.

Homemade drill bit. hacksaw for metal

Every master should always have a hacksaw for metal at hand. Having a set of blades made of a material of high hardness, you can cut not only metal products, but also hard woods, polymers and even ceramics. It takes a lot of effort and time to saw through such materials with a hand saw. A jigsaw is an expensive thing, and buying it for home handicraft work is not always profitable. Files for it are also expensive.

The drill bit described in this article works effectively like a jigsaw. At the same time, inexpensive canvases for metal and their fragments are used for work, of which there are always a lot in the workshop.

The offered nozzle for cutting metal has a simple design. It is easy to make it yourself. This homemade attachment fits onto a drill or electric screwdriver.

Below is the appearance of the finished device.

Drill and electric screwdriver: purposes, designs and principles of operation

Preparation for work

Homemade electric hacksaw for metal is assembled from the following elements.

Hilti band screwdrivers

The operational features of the tool are:

• Long-lasting and reliable lithium-ion battery. Hilti does not produce networked models.
• The presence of a limiter for the screw-in depth of the screw, which excludes its twisting.
• Pressing the start button once, after which the tool itself “remembers” the mode of further operation and acts only after the end of the self-tapping / screw rod touches the surface.
• Reversible drive.

Cordless to corded drill conversion without torque loss

• Hilti’s tape screwdrivers come with another spare battery and two removable auto feeders: one for wood and the other for drywall. Also included is a replaceable bit for fasteners with different head diameters.
• The manufacturer produces two types of tapes for powering the tool: for 40 and 50 self-tapping screws.
• Hilti also produces the SMD 57 attachment, the presence of which turns any screwdriver of this shape into a tape one. The model is equipped with a special dust blowing device.

However, such tape screwdrivers also have some disadvantages. In particular, the design of the chuck of the Hilti SD 5000 screwdriver does not allow to reliably drive self-tapping screws into the end sections of the plates that adjoin the corners. The fasteners have to be turned to the required depth, which is not very convenient with the mass setting of self-tapping screws. The screwdriver works stably only with “native” self-tapping screws from Hilti.

Reciprocating saw characteristics.

The main parameter that determines the performance of the tool. The more powerful the saw, the faster it will cut and the longer and more “toothy” the blade can be installed in it. True, along with the power, the weight increases noticeably, and for a tool that is always on hand, this is a serious argument against excess power. Together with the power, the price rises noticeably, and this is a serious argument for any tool. In addition, models with high power and a long heavy blade vibrate noticeably during work, and for such saws it becomes appropriate to install anti-vibration systems, which further increases the cost of the tool. Therefore, before choosing the most powerful model, you should decide how thick the materials you plan to cut. The maximum cutting depth is directly related to the saw power, so often the choice begins with the cutting depths of the tree and the cut. This is, in fact, the same power, only expressed in more understandable values. Indicates how long the blade can be placed on this saw without the risk of getting stuck in the material and overheating the tool. In fact, you can put a long blade on a low-power tool, and even cut with it, but the productivity will be small, and the risk of damage to the tool will be quite high.

A high speed of the blade is necessary for cutting hard materials: metals, stone, ceramics. While when cutting soft wood, productivity is only related to power, when cutting steel, the cutting speed also strongly depends on the maximum frequency of the saw. If the saw is supposed to be used for cutting materials of different hardness, a stroke frequency regulator is also required. If you carefully examine the blade up close, you can see that only the front. cutting. edge of the teeth is sharpened. The trailing edge of the teeth is not sharpened and, with the reverse movement of the blade, creates resistance, increasing the load on the engine and practically not increasing the depth of the cut. The pendulum stroke reduces this resistance by raising the file slightly during the return stroke. As a result, the saw performance is noticeably increased. Obviously, this function will only work with straight cuts. when there is free space above the back of the blade. When cutting curly lines, this function is better than power supply. Getting rid of the long, permanent tangling tail is the dream of any gardener working with garden electrical equipment. If the reciprocating saw is supposed to be used not at home, but “on the street”, the choice of a cordless tool can quickly justify itself. There are only two drawbacks to cordless saws, but both are significant. low power and high saw attachment. The ability to quickly change the blade without the use of additional keys or screwdrivers, of course, greatly increases the versatility and convenience of the tool. Unfortunately, it also increases the price. the simplest and cheapest models do not have this function.

An important parameter for a tool that is designed to work “by weight”. If the saw is supposed to be used in “uncomfortable” conditions, when it is not always possible to ensure a confident grip with both hands (for example, when pruning garden trees), it is better to choose a lighter model.

Some models are equipped with a soft start function

Without affecting the productivity of the work, this parameter, however, significantly increases the safety of the tool and its service life. The first is due to the absence of sharp jerks that could snatch the tool out of the hands when starting work. The second is due to the elimination of loads dangerous for engines that arise during such jerks. After choosing a model, you can take a closer look at it. does it have a support shoe? The ability to push the tool against the material being cut is often very helpful. In addition, a support shoe is almost essential if the saw is to be used to cut shapes from sheet material. Sometimes the shoe is not fixed strictly at 90 degrees, but can deviate, allowing you to cut at a given angle to the surface. This expands the capabilities of the tool, bringing it closer to jigsaws.

Manufacturers persistently prove that any manual labor can be mechanized. Electric drills replaced hand drills, and chainsaws replaced saws. What about a hacksaw? Yes, here is a network and battery saber saw, both for wood and for aerated concrete, capable of working on concrete, metal and even stone; how to choose it, we learn from the article!

Reciprocating saw device

Like any other power tool, a saber hacksaw consists of two parts: electrical and mechanical.

Reciprocating Saw: Alternative to Jigsaw, Angle Grinder and Chainsaw

What is a reciprocating saw and what is it used for? You will be surprised, but it can be a good alternative to a jigsaw, angle grinder and even a chain saw.

The reciprocating saw is a rather rare power tool in the homes of Russians, but in the west it has been used for quite some time. It looks a bit like a jigsaw, a bit like a hammer drill or a drill Now we’ll tell you what is special about it and how to choose a decent model.

Mechanical part

The principle of operation of mechanics is to transfer reciprocating movements to a fixed saw blade or nozzle. For this purpose, two types of “swinging” mechanisms are used: on the basis of a “drunken” bearing or using a gear train with a rod offset from the center.

In addition to the main components, some models can be equipped with a pendulum mechanism and a safety brake. The “pendulum” is used so that the canvas, making reciprocating movements in the horizontal plane, could move up and down. This increases productivity and reduces the load on the web.

Brake cushions impacts and jerks when the blade gets stuck in the cut.

There are professional models with anti-vibration system. Vibration compensation increases work accuracy and comfort.

Reciprocating Saw: Alternative to Jigsaw, Angle Grinder and Chainsaw

Reciprocating saw motor

A collector motor is used as a drive. It consists of a stator, rotor and brushes. The same motors are in electric drills, hammer drills, jigsaws and other tools.

The engine is started using a button. It can have built-in speed control. Sometimes the regulating component is installed separately.

Professional models may have an engine speed stabilization device. This ensures stable tool performance under load.

Dust collector

Usually, perforators are supplied with an active (using a vacuum cleaner) dust removal system, but for drills and screwdrivers, this topic is also very relevant. Therefore, some firms have proposed special compact containers that are attached to the surface in the working area and collect garbage while you are drilling without creating any forced draft.

In particular, Kärcher offered a completely unique solution. an elegant AA battery-powered micro vacuum cleaner, which is fixed in place using a vacuum.

Electric screwdriver attachment. DIY reciprocating saw

In this article, the author of the YouTube channel “Mistry MakeTool” will tell you how he made a reciprocating saw based on an electric screwdriver.

Materials Steel bar 10 mm thick. Bearing with 10 mm center hole. Steel plate. M6 bolts. Nails. Hacksaw blade. Steel square. The tools used by the author Drilling machine. Welding machine. File, file. Hammer. angle grinder, cutting and cleaning flap discs. Vise. Manufacturing process. So, first of all, the author puts the bearing on the steel bar, marks the place of the cut.

Then, holding the bar in a vice, makes a marking file with a file. Next. two oblique cuts on both sides of the bar, already using a wide file.

Now the bearing is put on the bar, and in the made slots it stands already at an angle.

Then the author welds the center of the bearing to the bar.

With the following details, the master makes two supports for the bar. He makes it from a thick steel plate. Marks center, cores, and drills holes.

Now you need to make the bottom for the device. and drill four mounting holes in it.

Having passed the bar into the side supports, the master tries on the cover, and marks the attachment points to the supports.

Drills and threads bolt holes.

Now pre-assembles the structure.

And marks the places for drilling holes for keys on the shaft.

Homemade “band” saw from a reciprocating saw

Not everyone has a band saw. However, in some cases, you can replace it with a homemade product from an electric reciprocating saw.

In this review, the author shows how to make a homemade “band” saw from a reciprocating saw with his own hands.

The first step is to remove the support sole from the saber saw, and cut off the sole itself, leaving only the mount. The author welds a metal corner to this mount.

You may also be interested in reading how to make a magnetic “broom” for cleaning in a workshop and garage.

Using a metal plate, we attach a second corner of the same to the corner, and we get something like a frame.

We make a fitting, after which we cut off all unnecessary, and we weld the guide support roller for the saw blade.

The main stages of work

At the next stage, we weld the frame to the profile pipe, on which the reciprocating saw will be located.

Further, the master welds an adjustable fastener from pieces of metal to the same professional pipe, the task of which is to hold the reciprocating saw during operation.

After that, it is necessary to cut out a piece of sheet metal, and then weld a small work table to the main structure, on which the workpieces can be supported.

We paint our homemade rig, and then attach the reciprocating saw. The whole structure is fixed in a locksmith vise, installed vertically on a folding platform.

You can watch the step-by-step process of work in the video below. The idea belongs to the author of the YouTube channel go TV.

Reciprocating Saw | HowStuffWorks

Reciprocating saw is a versatile and convenient tool for quickly cutting and shaping wood, plastic and even metal.

Homemade Ladder Saw. HomemadeTools.net

Homemade pecan ladder saw.

• Mini Vernier Height Gauge / Scriber / DIY Height gauge by DIYer on 2020-09-09 05:37:30
• Easy homemade vise from DIYer at 2020-09-09 05:31:40
• Pi count, use it to abuse or eat it? author: DIYSwede, 09.09.2020, 04:04:00
• A rod from an old worn out ball bearing from ananas studio diy on 2020-09-09 02:59:20
• Completion of the working end of the mowing line of woven plastic, desbromilow, 2020-09-09 02:27:45
• Bicycle hub section with internal gear. photo old kodger 2020-09-09 02:12:45
• Oven for beer kegs. part two. melting cans of Red Bull and Plate Checker from Retro Steam Tech at 2020-09-09 02:08:20
• Heavy-duty mask and filter. photo old kodger 2020-09-09 02:07:27
• Asuka cosplay. photo old kodger 2020-09-09 01:58:51
• light third arm made of armature from ananas studio diy on 09-09-09 01:29:57

Is this not what you are looking for? Try these:

• Home Repair Tools: Whether you prefer to use the Yellow Pages for anything that needs to be fixed around the house, or consider yourself a regular DIYer, there are several tools everyone should have in their toolbox. Learn all about them. in this article.
• Chainsaws: When you need a little more power or do a lot of work with a lot of cuts, a chainsaw is probably the best choice. The most common types are circular saws, reciprocating saws, and reciprocating saws. Check out this article for useful information about all chainsaws.
• Reciprocating Saw: The reciprocating saw is an enlarged horizontal version of the electric reciprocating saw. Find out how to use and maintain this chainsaw from this article.

.Homemade copy saw

Rules for the safe use of a reciprocating saw

It is especially important to wear protective goggles when working with an electric reciprocating saw. To use the reciprocating saw safely, select a blade suitable for the job, secure it securely in the blade holder with the blade retainer, then adjust the shoe to the desired height and slope for the job. If necessary, cut a starting hole in the material and insert the blade.

When you’re ready to cut, plug the saw into an electrical outlet, grip the handle firmly, align the blade near (not touching) the mark you want to cut, press the safety switch, then pull the trigger. Follow the incision mark slowly. When you are almost done, make sure the end of the material to be cut is held and will not split due to unsupported weight. For safety reasons, remember that teeth are sharp and should not be placed on surfaces where they can damage.

HomemadeTools.net

Homemade beech copy saw.

• Mini Vernier Height Gauge / Scriber / DIY Height gauge by DIYer on 2020-09-09 05:37:30
• Easy homemade vise from DIYer at 2020-09-09 05:31:40
• Pi count, use it to abuse or eat it? author: DIYSwede, 09.09.2020, 04:04:00
• A rod from an old worn out ball bearing from ananas studio diy on 2020-09-09 02:59:20
• Completion of the working end of the mowing line of woven plastic, desbromilow, 2020-09-09 02:27:45
• Bicycle hub section with internal gear. photo old kodger 2020-09-09 02:12:45
• Oven for beer kegs. part two. melting cans of Red Bull and Plate Checker from Retro Steam Tech at 2020-09-09 02:08:20
• Heavy-duty mask and filter. photo old kodger 2020-09-09 02:07:27
• Asuka cosplay. photo old kodger 2020-09-09 01:58:51
• light third arm made of armature from ananas studio diy on 09-09-09 01:29:57

How to maintain a reciprocating saw

Reciprocating saws or jigsaws should be periodically cleaned with an unused brush or air blower to remove sawdust. Dull or broken reciprocating saw blades should be replaced.

What is a reciprocating saw

A powered reciprocating saw uses a reciprocating motor to move a small saw blade up and down the object being cut. Blades available for wood (coarse or fine cuts), metal, drywall / plaster or plastic. Many reciprocating saws come with special blades or can be purchased individually for specific tasks. The handle has a safety button and a start switch. The blade holder has a blade retainer. Shoe. it is a plate that holds the blade at a certain distance from the job. A guide fence is also available for cutting straight lines.

Bushings

The bar that moves the blade has guide bushings. They are usually made from brass. Over time, they wear out, which leads to the appearance of backlash. The first signs are increased vibration during work and a deterioration in the quality of the cut. The malfunction is eliminated by replacing worn parts.

Reciprocating saw device and repair

Any workflow can be mechanized. Hand drills, planers, saws and other tools have long been electric. Not spared progress and the usual hacksaw. An alternative to her was a reciprocating saw.

The tool does an excellent job with its direct purpose. cutting with a blade. Using special attachments, you can not only saw, but also clean and process various surfaces. A saber hacksaw can handle almost any material. She saws wood and metal with equal ease. Even brick or concrete is no exception to the list.

Blade holder

During operation, the blade flies out of the fixing device. The malfunction is rare and is typical for cheap devices. This could be due to wear on the retainer.

Sometimes there is no breakage. Blade with the wrong shank will not hold firmly. There are frequent cases of fake consumables. In this case, the diameter of the hole and the dimensions of the back of the file may not coincide with the original. This leads to bad commit.

Reciprocating saw motor

A collector motor is used as a drive. It consists of a stator, rotor and brushes. The same motors are in electric drills, hammer drills, jigsaws and other tools.

The engine is started using a button. It can have built-in speed control. Sometimes the regulating component is installed separately.

Professional models may have an engine speed stabilization device. This ensures stable tool performance under load.

Electrical faults

Typical breakdowns include: malfunction of the speed controller or start button, wear of graphite brushes, poor contact in the terminals. Motor windings may be damaged. In all cases, you will have to purchase additional spare parts for the tool.

Gears

The worm gear experiences the greatest load. It drives the entire mechanism inside the gearbox. Depending on the design, a straight or bevel gear is used. Rotation is transmitted from a “worm” located at the end of the rotor shaft. It is he who wears out the most. The second place is taken by the gear, which can be worked out.

Reciprocating saw malfunctions and repairs

Any tool experiences stress during operation. Components and parts wear out over time, which leads to breakage. Each device is characterized by typical malfunctions associated with the failure of certain parts of it.

Mechanical part

The principle of operation of mechanics is to transfer reciprocating movements to a fixed saw blade or nozzle. For this purpose, two types of “swinging” mechanisms are used: on the basis of a “drunken” bearing or using a gear train with a rod offset from the center.

In addition to the main components, some models can be equipped with a pendulum mechanism and a safety brake. The “pendulum” is used so that the canvas, making reciprocating movements in the horizontal plane, could move up and down. This increases productivity and reduces the load on the web.

Brake cushions impacts and jerks when the blade gets stuck in the cut.

There are professional models with anti-vibration system. Vibration compensation increases work accuracy and comfort.