The lawn mower when working stalls what the reason. The lawn mower stalls when pressing…

Why the lawn mower stall: the most common reasons, their diagnosis and elimination

A gasoline trimmer for grass is a useful tool for cleaning from unnecessary grass of house territories and large area lawns. The design of this technique is quite complicated, therefore, if the device breaks, there may be several reasons. The most likely factors that have caught a breakdown are usually described in the user guide. Knowing why a trimmer for grass stalls, you can try to independently eliminate the defect. The most common malfunctions provoking the motorcycle stops, and the ability to repair them with your own hands is in the material further.

A gasoline trimmer for grass is a useful tool for cleaning from unnecessary grass of house territories and large area lawns. The design of this technique is quite complicated, therefore, if the device breaks, there may be several reasons. The most likely factors that have caught a breakdown are usually described in the user guide. Knowing why a trimmer for grass stalls, you can try to independently eliminate the defect. The most common malfunctions provoking the motorcycle stops, and the ability to repair them with your own hands is in the material further.

5 minute fix for a lawn mower that starts then stalls

If stalled under load

Sometimes a trimmer for grass stalls under load, as it cannot gain momentum. This means that the cable stretched in the carburetor is weakened and sagging. If there is experience in repairing this node, the cable should be pulled.

Another cause of the malfunction. the fuel hose is stretched overly. With a load, it is even more stretched, as a result of which cracks are formed, as a result, the part deteriorates. To eliminate the breakdown, you need to replace this element.

When pressing gas

If the lawn mower stops when pressing the gas, then the reasons may be the following.

  • The most common option is a fuss of adjusting the carburetor, which occurs with significant loads on the drive, after a prolonged inaction of the mechanism or when it is used in severe conditions.
  • The clogging of the fuel valve, which eliminates it with the message, as a result of which gasoline according to the system begins to flow normally.
  • The weakening and hanging of the cable in the carburetor. Also, a tensile of the fuel hose can occur up to its rupture, caused by the action of a significant load.
  • Clogging of the saapun (check valve), as a result of which fuel does not enter the tank.

If the problem is associated with the carburetor node, then it can be recognized by the appearance of vibrations of the lawn mower. Когда лопается шланг или растягивается трос — выполняют замену данных комплектующих.

What could break

Malfunctions with a benzocosa associated with the fact that this device is not started, in a certain way are classified by specialists of service services. They stand out malfunctions with the following nodes of the mechanism:

  • the engine in which the piston and bearings can be worn out or fail to crack the crankcase;
  • the fuel supply system, while it is possible to clog the filter or problems with the carburetor;
  • mechanical damage to wires, tubes, hoses;
  • The ignition chain.

To correctly determine the knot where the breakdown occurred, it is necessary to pay attention to the circumstances of the trimmer stalls for the grass.

Ways to eliminate breakdowns

Subsequent work is likely on the carburetor:

  • cleaning and adjustment of the fuel supply valve;
  • similar work with a valve producing redesigned gases and pairs (after burning fuel);
  • replacement of the spring more weak on the entrance valve;
  • restoration of the tension of the carburetor cable;
  • replacement of the fuel leaks hose, verification and strengthening of a weakened connection;
  • changing the rotor damper disk;.
  • Change of faulty wire or ignition coil.

Immediately after the start

Smelting Motokos or a trimmer for the grass after starting is justified by subsequent reasons:

  • impressive of previously adjusted valves;
  • first the wrong settings of the valve mechanism;
  • clogging with deposits of the fuel supply valve;
  • the hose is worn or poorly annexed.
lawn, mower, working, stalls, reason, pressing

Due to the violated method of injection of a fuel, a lawn mower or a trimmer for grass is very vibrated in work.

The gasoline trimmer for grass stalls at idle

Often, when reducing the speed, the motor motorcycles stalls and does not support idle speed when re.starting. The main reasons for the occurrence of such a breakdown include pollution or the dumping of the carburetor, as well as clogging of the air filter.

Gasoline trimmer for grass stalls at idle

In case of violation of the optimal settings of the carburetor, it is necessary to clean it and repeated adjustment. You can cope with clogging the air filter of a trimmer for grass by placing it for several hours in a solution with a conventional domestic detergent. If independent cleaning has not helped to cope with the blockage, it is better to purchase a new filter element in accordance with the operating manual.

After the measures, the user will not encounter a situation for a long time when a trimmer for grass stalls in idle and functions only when gas supplies.

lawn, mower, working, stalls, reason, pressing

They brought a Chinese benzotrimmer for repairs (they said it turned in the back, we are undergoing to start like.

Apart from time to time, from time to time, gasoline trimmers for grass can stall due to the fact that the valve located in the gas tank cover just clogged or stick. To find out, try to use the braid by loosening the gas tank cover. If in this mode the device is working on a dull way, clean the valve.

over, the lawn mower can stall due to the disgusting receipt of fuel in the carburetor. Nevertheless, repair t.e. It works normally at low speeds. Why then the device starts up, ask you? The reason for this is that at first, the fuel gradually runs into the carburetor and is enough to work at high power. The lawn mower does not work at idle. But then it is produced and at huge turns the engine begins to stall. As for the carburetor, here the problem may also consist in the fact that its body is very pulled.

lawn, mower, working, stalls, reason, pressing

In addition to everything else, do not forget to check the fuel intake hose. The inconsistent may be that it holds weakly or in general cracked.

These are the main prerequisites why the lawn mower can stall.

Air filter

On the pages of the global network, you can find information that the chainsaw of the Stihl 180 can stall due to severe air filter pollution. I would like to refute this not absolutely true information, and say that the STIHL carburetor MS 180 is equipped with a compensator, which is designed and installed in order to make an air focus necessary for the usual operation of the Stihl 180 chainsaw, bypassing the dirty filter. Of course, the power with a clogged air filter will fall a little, but it will definitely not stall. Another capacity may fall due to the wear of the piston, here the repair of the piston chainsaw of the Stihl MS 180 will already be required.

Forbidbenzokos when clicking on gas: causes of their solution.Glumpnbenzokos (trimmer for grass):. Fighting.

  • idle sensor failure;
  • clogging of the throttle;
  • work of the sensor of the position of the trissellain;
  • Injector or carburetor pollution

The grounds for breakdown can be completely different, therefore, when eliminating them, it will be necessary to operate with all kinds of actions and techniques. If your shoulders are considerable driver’s experience, and you know the features of the car’s work as your five fingers, regardless of the model, then the elimination of this kind of malfunctions will not cause you any problems. And all because such breakdowns are not complex or serious. It follows that you can establish the operation of the car without outside help. Well, if the level of awareness or lack of free time will not give you the opportunity to eliminate all defects yourself, it is better to seek help from knowledgeable people who can save you from unpleasant moments in the shortest possible time.

What could break

Problems with a benzocosa associated with the fact that this device is not started, specially classified by specialists of service services. They stand out malfunctions with subsequent nodes of the mechanism:

  • the engine, in which the piston and bearings can be worn out or out of order, crack the crankcase;
  • the fuel supply system, with all this, can be clogging the filter or difficulties with a carburetor;
  • mechanical damage to wires, tubes, hoses;
  • The ignition chain.

When working idle

Having launched a trimmer for grass or a motorcycle at idle, you find that the device is starting up. but it swallows, after working, say, 5-10 minutes. The prerequisites here can be subsequent:

  • clogging, violation of carburetor adjustment;
  • Initially, incorrect configuration of the valve mechanism of the carburetor;
  • air filter clogging;
  • reducing the speed of the gearbox (if any). the incorrect ratio of fuel.air consistency;
  • clogging the throttle;
  • penetration of excess air into the fuel system;
  • The fuel ends in the tank (and oil in the tank, if the engine is four.stroke).

In the presence of troubles specifically with the carburetor, the machine will stop both after a cool start and after starting on the already worked engine.

The trimmer for grass stalls. how to eliminate the problem

A gasoline trimmer for grass is a useful tool for cleaning from unnecessary grass of house territories and large area lawns. The design of this technique is quite complicated, therefore, if the device breaks, there may be several reasons. The most likely factors that have caught a breakdown are usually described in the user guide. Knowing why a trimmer for grass stalls, you can try to independently eliminate the defect. The most common malfunctions provoking the motorcycle stops, and the ability to repair them with your own hands is in the material further.

In order to most accurately determine the cause of the trimmer malfunction for grass of any brand (for example, echo) and find out the possibility of eliminating it, you need to install, when performing what action the device stalls. The engine can turn off both at idle and at high speeds, heated under load or immediately after starting and t.D.

If you stalled after gas supply

Owners of gasoline braids often mention that the lawn mower stalls when you press the gas. Usually such a breakdown occurs due to problems in the carburetor. A failure in his work can occur due to long-term storage, use in difficult conditions, significant overload of the motor. The symptom of such a breakdown will be vibrating movements of the device during operation.

On a note! Users familiar with the repair of a car carburetor can try to restore this important node of the trimmer for the grass on their own, using the instructions for operating. Otherwise, the correct decision will be to seek help from the service center representatives.

Sometimes a trimmer for grass stalls when you give gas because the fuel valve is clogged. This interferes with the supply of gasoline. To eliminate the problem, it is enough to loosen the valve. Thus, normal supply of carburetor fuel will be restored.

Another possible reason why the lawn mower stalls when gas is supplied is pollution of the soundtress (check valve). This detail prevents the appearance of a vacuum in a gas tank. If it is clogged, the air does not flow, which means that fuel does not go to the carburetor. To eliminate the problem, it is necessary to clean this element.

If it stalled at high speeds

If the carburetor stalls at high speeds, this means that in idle and small there are enough incoming fuel, and to work on high is not enough. Then it is necessary to check the serviceability of the following nodes of the trimmer for the grass.

  • Fuel hose. its integrity could be violated as a result of cracking. In this case, you need to replace the part. Or maybe you just need to tighten the clamps.
  • A filter network between a carburetor and a hose for supplying a gasoline mixture-it could clog. In this situation, it is necessary to clean the detail.
  • The valve on the gas tank cover. he could stick or clog with garbage. Cleaning is also necessary.
  • Carburetor. perhaps as a result of constant vibration, it was resolved. This is usually characteristic of cheap Chinese details. To eliminate the problem, it is necessary to set up according to the instructions. In some cases, it is enough to only weaken the tightening of the carburetor case. If the adjustment is not possible, it is necessary to install a new element.
  • Additionally, check the air filter. Perhaps it will need to be washed and cleaned or replaced with a new one, as he could clog with dirt and particles of grass when tilted technology, when the user mowed in hard.to.reach places.

If you stalled during work idle

If the lawn mower stalls, working idle, there may be several factors reasons.

  • First you need to check the prepared fuel solution, when it comes to a four-stroke trimmer working on a gasoline-oil mixture. There is a chance that it is made incorrectly. the proportions are not withstanded. Because of this, the gearbox is warming up, and the revolutions on the drum are lowering.
  • Another probable cause is blockage of elements such as a throttle, air filter or carburetor. You need to clean the indicated details.
  • Another possible factor is to resolve or incorrectly carried out carburetor adjustment. You need to adjust the setting according to the instructions.
  • Observe this problem mono and when opening the air damper. In this situation, the lack of fuel for a trimmer for grass occurs through the fault of the air flow.

If the device does not have enough fuel, it works properly at high speeds or when they increase, but stalls at idle. If the root of the problem consists in the carburetor, the lawn mower will be disconnected both with cold startup and hot.

If you stalled after starting

If the technique starts and stalls immediately after starting, this indicates the wrong settings or deducting the device. As a result of this, the fuel enters the engine unevenly, which leads to significant vibration and disconnecting the trimmer for the grass. To fix the breakdown, it is necessary to reconfigure the device according to the user management.

Another probable problem is the blockage of the valve supplying the gasoline mixture. It must be cleaned.

On a note! If the trimmer for the grass starts, but immediately stalls, it may also mean that the fuel is moving to the carburetor with difficulty. Weakening the valve will help to eliminate the problem. this will provide uniform and free circulation of fuel in the device.

Another possible reason is the damaged fuel intake hose. Air can penetrate through cracks and holes into the system. To solve the problem, you need to increase the engine speed in order to get rid of air bubbles that have penetrated the device.

If you stalled when opening the damper

If the technique works properly at idle, but stalls when opening an air damper, this reports about the penetration of air into the system through cracks in the fuel supply hose or damaged oil seals. To fix the breakdown and establish the work of the tool without driving air from the atmosphere, it is necessary to replace damaged parts.

Preventive measures and operating rules

So that the lawn mower does not work and does not stall when starting, it must be correctly stored and operated. Compliance with the following simple recommendations will forget about problems.

  • When begging the grass, you need to monitor the state of the cooling system. It is also necessary to regularly clean the channels in the case and starter’s ribs.
  • To clean the tool, you should use kerosene, solvent, or other washing tools.
  • You can not clean a hot tool. it must cool before washing.
  • It is important to observe the recommended working mode. this will avoid overheating of the engine.
  • If a braid for grass is not used over the next thirty days, the fuel must be drained, otherwise it will fall into heavy components that can score the channels of the carburetor.
  • After the fuel is merged, the trimmer for the grass should work at idle for some time until it turns off. This will allow you to completely get rid of the rest inside the working mixture.

To store the tool in cold weather, you need:

  • completely drain the fuel;
  • disassemble the lawn mower, wash and clean all available components;
  • inspect the condition of the parts, eliminate all defects that can be corrected;
  • pour the required amount of oil into the gearbox;
  • Clean the air filter;
  • perform partial disassembly of the engine, wash all moving parts, blow and lubricate thoroughly;
  • To lubricate the piston, unscrew the candle, then raise the piston to the upper dead point by the starter, pour a small amount of oil into the hole for the candle and do the crankshaft several times.

Important! If there is no way to store a trimmer for grass in a warm dry room, you must first wrap the motor with an embarrassed rag.

Only by observing these rules, you can be sure that the lawn mower will work properly and will not stall for a number of seasons.

As you can see, stopping the work of a trimmer for grass can be caused by many reasons. Most of them can be fixed independently using the user instructions. In cases where there is no self.confidence, the equipment is recommended to be attributed to repairs. It is worth remembering that incorrect actions can cause even greater harm to the trimmer. As a result, the repair of Motokos will cost a much larger amount than it would be initially, and in the worst case, it may be necessary to buy a new unit.

The lawn mower stalls when you press the gas

The hole in the fuel cover (saepun) of a trimmer for grass

With a similar problem, it is worth paying attention to the fuel valve, which, when clogging, ceases to normally pass the fuel mixture. By solving this malfunction, it is weakening using a suitable tool. In addition, the problem with the circulation of the fuel mixture may cover in the contamination of the valve. To do this, just blow it with a stream of compressed air.

If you stalled when opening the damper

If the technique works properly at idle, but stalls when opening an air damper, this reports about the penetration of air into the system through cracks in the fuel supply hose or damaged oil seals. To fix the breakdown and establish the work of the tool without driving air from the atmosphere, it is necessary to replace damaged parts.

Another possible reason for the breakdown is the malfunction of the carburetor dosage system. To eliminate this problem, it is better to contact professionals.

lawn, mower, working, stalls, reason, pressing

At high speeds

When a braid for grass stalls at high speeds, this is due to the following problems:

  • clogging or clutching a valve located on the gas tank lid;
  • The carburetor was diluted under the influence of vibrations arising during the operation of the mechanism;
  • problems with the circulation of the fuel mixture;
  • atmospheric air
  • The hose intended for fuel fuel cracked or slightly connected.

The carburetor is regulated by relying on the operational instruction to the trimmer. For configuration, it is often enough to weaken the tightening of its body. If there are problematic issues with the circulation of the fuel mixture, then it can gradually enter the carburetor. After its production, the engine stalls at high speeds.

At high speeds

When a braid for grass stalls at high speeds, this is due to the following problems:

  • clogging or clutching a valve located on the gas tank lid;
  • The carburetor was diluted under the influence of vibrations arising during the operation of the mechanism;
  • problems with the circulation of the fuel mixture;
  • atmospheric air
  • The hose intended for fuel fuel cracked or slightly connected.

The carburetor is regulated by relying on the operational instruction to the trimmer. For configuration, it is often enough to weaken the tightening of its body. If there are problematic issues with the circulation of the fuel mixture, then it can gradually enter the carburetor. After its production, the engine stalls at high speeds.

Malfunctions leading to improper operation of the chainsaw

There are a number of malfunctions that must be taken into account in diagnosis, t. to. They can lead to the interruptions of the saw.

  • Damage to the crankshaft bearings. With worn crankshaft bearings, the appearance of a beating on the main shaft is inevitable, where the flywheel is attached. In such a situation, it is impossible to adjust the gap between the flywheel and the ignition coil, which entails interruptions in sparking, and unstable work of the chainsaw.
  • Pollution of the pulse channel. The pulse channel serves to ensure the operation of the fuel pump, respectively, its pollution leads to improper operation of the pump, which will make it impossible to operate the saw (it will be launched and immediately stall).
  • Wear of the CPG. As a rule, with increased wear of CPH, a decrease in compression in the chainsaw engine is observed, which is necessarily affecting its ability to develop momentum.
  • Fuel and air filters pollution.

What to do if the engine does not start?

If the lawn mower fails is not possible, then the first thing is to check the presence of fuel in the tank and its quality. For refueling the tool, it is recommended to use high-quality gasoline purchased at gas stations, the brand of which should not be lower than the AI-92. Savings on cheap fuel can lead to a breakdown of the cylinder-piston group, for the repair of which a third of the cost of Motokosa itself can take. It is equally important and correctly preparing a fuel mixture of gasoline and oil. The proportional ratio of these components of the mixture is indicated by the manufacturer in the manual. Do not prepare the fuel mixture in large volumes, since during long storage its properties are lost. It is better to use a freshly prepared mixture.

When preparing the fuel mixture, pour the oil into gasoline using a medical syringe that allows you to accurately comply with the necessary proportion of the components

Fuel filter pollution in the tank may also prevent the operation of the lawn mower engine. Therefore, when problems with the launch of the motor, check the condition of the filter. If necessary, replace the filter. It is forbidden to leave the incoming pipe without a fuel filter.

The air filter also needs to be in the test. During contamination, the part is removed, in the field is washed in gasoline and put in place. In the country or at home, the filter can be washed in water using detergents. After that, the filter rinses, squeezes and dries. The dried filter is moistened with a small amount of oil used to prepare the fuel mixture. Excess oils are removed by compressing the filter with hands. Then the part is installed in place. The removed cover is placed back and fixed with screws.

The air filter washed in the fuel mixture, squeezed and dried, is installed in place in the plastic case and covered with a lid

How this procedure is done in more detail you can look at

If all of the above procedures are carried out, and the engine is not started, then adjust its revolutions at idle, twisting the carburetor screw. In the video posted at the beginning of the article, attention is paid to this issue.

  • Put the tool on the side so that the air filter is at the top. With this location of the chainsaw, the fuel mixture is ensured exactly into the bottom of the carburetor. On the first attempt, the engine will start if you remove the air filter before starting and pour a few drops of the mixture into the carburetor, and then install the dismantled parts to the place. The method is tested in practice.
  • If the first advice does not give a result, then, most likely, the problem in the spark plug. In this case, unscrew the candle and check its performance, as well as dry the combustion chamber. A candle that does not show signs of life, replace the new.
  • If the spark plug is in good condition, the filters are clean and fuel mixture, then you can use the universal way of starting the engine. Close the carburetor air damper and pull the starter handle once. Then open the damper and pull the starter 2-3 times. Repeat the procedure from three to five times. The engine will surely start.

Some pull the pen with such force that it is necessary to repair the starter of the lawn mowed with their own hands. This is possible only in the case of a gust of a cable or breakdown of the cable handle. In other cases, it is recommended to replace the starter. This node is sold in the collection.

Carburetor adjustment and configuration

The maximum and minimum engine speeds, even idle is regulated by the carburetor. The stable operation of the lawn mower depends on the amount of fuel mixture and air. The lawn mower is not started with disturbed adjustment of the carburetor. The procedure for setting up the device for supplying fuel at low speeds (L), high speeds (H) and idle (T) is regulated by the same vints:

  • The chainsaw should work for at least 10 minutes, since the adjustment is carried out in hot.
  • The screw n is flooded smoothly to maximum speed, then turning on ¼, counterclockwise, reducing the speed of rotation of the engine shaft.
  • The idle stroke is regulated by the screw T, ensuring that the braid for the grass does not rotate.
  • The screw l is regulated, first opening the throttle as much as possible, and then smoothly reducing the speed to stable minimum.

After adjustment, a proper carburetor with cleaned filters should ensure the operation of the engine. In the event of a malfunction of the carburetor, after its repair, it will again need to configure the supply system before starting the lawn mower.

Rare breakdowns that prevent the operation of the lawn mower can be:

The most important malfunction, the elimination of which is associated with the replacement of the engine may be the failure of the piston group of the engine. Why does a lawn mower or a lawn mower stall when you press gas, at idle, when heated and other causes of non.taxes of a gasoline trimmer for grass. The cost of repair will cost about 70% of the cost of the product. The lawn mower stalls or a trimmer for STIHL grass stalls when why Chinese. To figure out the reasons why the lawn mower is not starting up will help

At idle

At single speeds, the common reasons for stopping a trimmer for grass are as follows:

  • reducing the speed of the gearbox when heating it, which is a consequence of the use of inappropriate fuel mixture;
  • clogging of the throttle;

If a carburetor is a problem place, then the technique will stop at the “cold” and with a “hot” launch.

Diagnosis of malfunctions

The user first needs to check if there is a fuel in the tank. Starting in agreement with annotation, putting the saw on the side. Set the air damper to the position “Closed”, pump up fuel, turn on the ignition and produce 3-4 sharp jerks by the starter. If the engine has earned, open the air damper. The lawn mower is not started. we repeat the operations with a slightly open air damper.

The lawn mower cannot work for a long time. Gearbox and engine will overheat. Mowing less than 15 = 20 minutes, taking a five.minute break. In hot noon, the operating time is reduced by half. When mowing weeds, sedgers, the working hours are required to reduce.

If you are unsuccessful, we begin to find the reason for the refusal:

  • check the quality of fuel;
  • make sure the operability of the candle and the cleanliness of the candle canal;
  • check the cleanliness of the air filter;
  • Make sure that the fuel filter is not clogged;
  • Check the cleanliness of the bastard;
  • Clean the exhaust channel.

complex reasons will be detected in the diagnosis of a malfunction, leading to the overhaul of the carburetor. Such reasons include clogging of the internal channels of the carburetor, wear on it gaskets and violation of the tightness of internal halls with a vacuum loss. DIY lawn mowing repair, if it does not start, will require patience.

Why and what to do if a trimmer stalls for grass

There are several reasons why the trimmer for grass stalls when the grass. Usually the problem is provoked:

  • wear of engine elements. piston, bearings, crankcase;
  • malfunctions with fuel supply. a carburetor can fail in the device, sometimes a malfunction causes a clogged filter;
  • mechanical damage to hoses, tubes and cables;
  • disobedience with the ignition chain.

Most often, under a load for one reason or another, an old trimmer for grass, which has long been in operation, stalls for a particular reason. But sometimes the owners of new gasoline devices face problems.

Why is a trimmer for grass stalling when pressing gas, increasing speed

If the trimmer for the grass stalls when you give gas, then the problem is usually a malfunction of the carburetor adjustment. The malfunction often occurs if the device was inaction for a long time, and then received a significant load. Sometimes the unit stalls immediately after increasing speed, if before that it was operated in difficult conditions with violation of the rules.

The following reasons are also leading to problems with the performance of the device:

With stretching or rupture of the fuel hose in the gasoline trimmer, the elements that have become unusable must be changed. If the reason is in the clogged valves and filters in the unit, they are quite simple to clean.

If the reason that the trimmer stalls for the grass is caused by problems with the carburetor, the problems are accompanied by vibrations

Another common problem is that the trimmer for grass stalls with increasing speed due. In this case, you need to find the instructions for the device and carry out the reconfiguration of the unit. Often it is enough to weaken the tightening of the carburetor body.

Pt 1 How To Cut Tall Grass with Cheap Lawn Mower. Mowing Tall Overgrown Grass

Why does a trimmer for grass stall at idle

Garden trimmer for grass often stalls even at idle. The reasons for the malfunction are usually simple. First of all, the improper adjustment of the carburetor affects performance. it leads to problems both at high speeds and in idle mode. Turning off the device can provoke clogging of an air filter or throttle.

Sometimes a trimmer for grass stalls if incorrect fuel is used for it. The gearbox for this reason overheats and reduces momentum.

If a malfunction occurs, it is necessary, first of all, to inspect the carburetor unit and perform mechanical repair or configuration. If the cause is of poor.quality fuel, you need to replace the mixture with a more suitable.

What to do if the trimmer for the grass starts and immediately stalls

If the trimmer for the grass does not gain momentum and stalls immediately after starting, the problem usually consists in improper tuning the carburetor. In this case, fuel in the system comes unevenly, the gasoline unit vibrates and cannot work normally. Repair consists in reconfiguring a carburetor unit according to the instructions from the manufacturer.

Engine stop causes fuel supply valve. The element must be carefully cleaned, and then installed back in place. If the lawn mower still stalls immediately after starting, perhaps the valve is too tight and it needs to be loosened. In this case, the fuel mixture will begin to circulate through the system freely, and problems with the performance of the unit will disappear.

In some cases, a gasoline trimmer for grass stalls due to the fact that the hose contains damage that pass the air. During the repair, you need to replace the fuel tube with a new.

Attention! If the damage in the hose is insignificant, it is allowed to simply add a revolution drive. This will allow you to drive out air bubbles from the fuel system.

What to do if the trimmer works and stalls for the grass

Owners of garden gasoline units are faced with the fact that a trimmer for grass stalls at large speeds after a short work. First, the device begins to function with jerks, and then gradually stops.

Typically, the reason is the overheating of the system. gasoline in the carburetor simply boils. A trimmer for grass can heat up if the ignition circuit coil or wire is damaged. There is no point in repairing worn details, they are simply changed to new working.

The use of a trimmer for the grass does not lead the use of not disk, but rotary damper in a carburetor

What to do if the trimmer for the grass overheats and stalls

If a hot trimmer stalls for grass, the situation is a great danger to the performance of the unit. Repair should be carried out immediately, otherwise the device will be completely unusable, and it will be more difficult to restore it.

Overheating of the unit usually cause the following reasons:

  • The use of inalitions. pour fuel into the tank with precisely with such an octane number that is recommended by the manufacturer;
  • a large amount of air in the system. for this reason, the enriched mixture releases an excess of heat;
  • non.compliance with the proportions of oil and gasoline in the preparation of fuel;
  • The thick layer of soot on the muffler. soot is a good heat.insulating material, the gasoline braid for the grass during operation is very hot and stalls;
  • The displacement of the axis of the spit.headed head inside the bar. for this reason, the rotation slows down, and the load on the engine increases.

If the gasoline unit stalls, you need to carefully examine it and eliminate first of all possible deformations of the structure. Then it is necessary to study the fuel parameters. If they do not correspond to the recommended, gasoline is replaced with a more suitable. If unnecessary air gets into the system, it is necessary to independently or with the involvement of specialists to adjust the position of the carburetor damper.

Sometimes a gasoline trimmer for the grass overheats and stalls because there is too old fuel in the tank. Use a fresh mixture for the unit, which was stored no longer than two weeks.

Attention! A trimmer for grass will overheat if you use it for too long, or mow with a weak device hard thick grass.

How to avoid breakdowns

Many breakdowns of a gasoline trimmer for grass can really be eliminated if you remove the causes, but if possible, it is recommended to, in principle, avoid faults. Simple measures allow to maintain the unit in a working state:

  • You need to use a trimmer for grass in accordance with the recommendations of the manufacturer. It is impossible to use a weak device for removing hard weeds on the site, it is also not recommended to use motorcycles in excess of the due time. The gasoline unit needs to be turned off regularly and allow it to cool down.
  • During the operation of the device, it is necessary to monitor the state of the cooling system. To maintain performance, the channels in the case are regularly cleaned, like the starter’s ribs. The clogging of the system often becomes the reason that the unit stalls from overheating.
  • After using the gasoline trimmer for the grass, too, you need to clean. In this case, the procedure is not carried out for a hot unit, at first it must completely cool. For cleaning, use solvents, kerosene and other products allowed for use by the manufacturer.
  • Before cleaning, the motorcycles for storage must be drained from the tank, the remains of unused fuel. If this is not done, the gasoline mixture will fall into heavy components and will clog the channels of the carburetor, which will subsequently cause malfunctions. After draining the fuel, the device is launched at idle and waited for it to turn off.

With the onset of autumn, a gasoline trimmer for grass must be correctly removed for storage. First, the residues of the fuel mixture are drained from the device, and then the unit is disassembled, rinse and clean all removable components.

Before cleaning gasoline motorcycles for storage, you need to evaluate the condition of its parts, carry out the necessary repair and replacement of nodes. Air filter needs to be cleaned. The engine is partially disassembled, rinsed and blown by moving elements, and then applied a new grease. To maintain the piston part, the candle is unscrewed and the piston itself is lifted to the top point, and a little oil is poured into the opening opening and the crankshaft is twisted several times.

Store a gasoline trimmer for grass in winter is necessary in a warm room