Tiller DIY Motor Scooter Engine Ant

Engine from Tiller to Ant

tiller, motor, scooter, engine

Auto mechanic specializing in agricultural machinery

Agricultural machinery used in household plots, fields, vegetable gardens and summer cottages is currently a fairly technologically advanced device. It is almost impossible to find a person who has not used a tiller or cultivator to facilitate the labor associated with working on the soil.

You can choose a tiller for every taste and budget, or you can make it yourself. Often the motor from the unit is used to make a full-fledged scooter, which is also indispensable for farmers, because the movement of goods over long distances is always required. Consider how to make a motor scooter Ant with an engine from a home tiller.

Use a tiller motor to give life to a new device

How to install the engine from Tiller Ant

Work on installing the engine from the Tiller Ant should begin with moving the motor. Then it is recommended to adhere to a certain plan in order to get a high-quality and reliable unit:

  • Frame manufacturing. This is done by welding a sheet of iron to a 4mm diameter pipe. The frame must be firmly attached to the engine.
  • Installing the carburetor, air filter and muffler.

Important! A cooling cover must be fitted to protect the unit from overheating.

In this video, consider an ant on a tiller engine:

Attention! You will have to open and close the carburetor flap manually.

  • we install the wheel in the front of the tiller, and the level of plowing depth and ease of control will depend on the correct attachment;
  • we make nozzles from pipes and corners, fix them with a key in special grooves and, so that there is no movement along the axis, we fix them with bolts;
  • we determine the level of capture of about 1-1.2 meters, depending on the work performed.

The unit based on the motor scooter Ant will turn out to be a little bulky, weighing about 90 kilograms, and slightly clumsy. But special maneuverability in the garden and in the field is not required, since there are usually no obstacles that must be frequently bypassed. But the motor will perfectly withstand all loads, even with long and continuous operation.

Homemade Motorized Scooter Using 2 Stroke Engine | DIY Scooter

When a home-made Ant with a motor from a tiller needs to be moved a long distance, then in the manufacture of equipment it should be possible to install wheels that are bolted through, or make an additional stand for transportation in the back of a truck or in a trailer.

It is also possible to make the wheels smaller and attach a plow, potato digger or tiller.

Reviews

Vasily, 32 years old

“The old Ant has been gathering dust in the garage for several years. After looking at several relevant articles on the Internet, I decided to adapt the motor from the tiller to it. It turned out to be an excellent au pair, an economical and reliable unit. And do-it-yourself production of Bosch would be much cheaper if I bought a new device. “.

“Combining Tiller and Ant is a great idea, which miraculously came to mind. Having made the equipment, I received a unit that perfectly copes with all agricultural work on my personal plot. It not only loosens and digs up the soil, but also helps in harvesting and transporting various heavy loads. I am very pleased with the new technology. “.

2 Ant-1. characteristics and features

Tiller Ant-1 (First) is intended for cultivating sandy and clay soil and preparing it for planting vegetables.

Also, with the help of the Ant, you can cultivate dry, loose soil.

  • engine model. BS170F / P;
  • engine power. HP 7;
  • number of speeds. 1 backward and 2 forward;
  • fuel tank / crankcase volume. 3.6 l / 0.6 l;
  • transmission. belt-chain;
  • plowing depth. 100-300 mm;
  • plowing width. 750 mm;
  • completeness from 4 to 6 cutters;
  • launch. manual;
  • wheel size. two wheels 4.00-8 “;
  • weight up to 90 kg.

2.1 Tiller Ant

1.4 Chain reducer

The two-stage chain reducer can reduce the rotational speed and increase the torque that is transmitted from the output shaft of the power unit to the rippers or wheels.

Homemade reducer for tiller

A popular solution is the use of an assembled gearbox from a motor scooter Ant. It is enough to install rollers on the bridge of the future tiller so as not to use the entire wheeled platform from the scooter. This choice of chain reducer results in the ideal ratio of driving speed and tiller power.
to the menu

How to make a tiller with your own hands based on a motor scooter Ant?

At present, the development of agricultural machinery has reached a high level of development. It’s hard to imagine a modern farmer without a cultivator or tiller.

1.3 Tiller engine

In the manufacture of such a unit, you can use a two-stroke gasoline engine from the Ant motor scooter. Such an engine has forced air cooling and this is an undoubted advantage at low speed in order to avoid overheating. The engine is interlocked with a four-speed gearbox. To reduce the cost of the unit and reduce the size of the tiller, you can make a muffler with your own hands, using parts from a factory muffler from a motor scooter. The exhaust tract is positioned to the side, and the muffler itself is inserted into the exhaust cylinder.

The engine is started using a kickstarter, the speeds are switched using a lever located on the box with sectors. It is necessary to lengthen the gear shaft by 170 mm in order to integrate the overrunning clutch. The driven sprocket is attached to the end of the left shaft. Due to the rotation of the shaft, the coupling interacts with the roller and the roller is set in motion.
to the menu

1 tiller based on motor scooter Ant

For practical and convenient use of the tiller, it can be made from an old motor scooter Ant. On such a technique it will be convenient to move around the cultivated area, transport the grown crops, humus, agricultural tools, even firewood, garbage and much more.

Brand Tiller Ant

1.2 Tiller frame

All elements of the tiller are located on the frame. The frame structure consists of two side members, which are made of quarter inch steel pipe. The front and rear ends of the side members are bent upwards, the rear ends must be bent towards each other, then welded together. In the manufacture of steering, you can use the motorcycle “Izh” and its spare parts.

Homemade tiller with a motor from Ant

The steering structure from the motorcycle is welded to the rear ends of the side members by welding. To tension the chain of the first stage of the transmission, it is necessary to connect the side members along the length with several cross members. The platform for the battery and other parts also serve as crossbars. The gearbox housing, which is part of the frame layout, in addition to its functions, also performs the function of a rack between the chassis and the power unit. For the transport of goods by a trailer, a two-axle bogie can be hooked up to the lower rear of the crankcase.
to the menu

1.5 Homemade wheels

It will be difficult to move on such a mechanism when loosening or in a snowy season if ordinary wheels from a scooter are installed on it. The rippers that are installed on the future tiller are homemade. Wheels are selectable 5-10 inches. In order to increase the grip of the wheels with the ground, you need to put on a homemade bandage on the wheels. Such a bandage can be made of steel strip.

Its cross-section may be different, but the optimal one will be 90 by 5 mm. The lugs are made from a 25 mm corner and welded to the steel strip. To avoid slipping of the lug band, antennae are welded to it, which are bent into the inside of the disc.

In a tiller based on the Ant motor scooter, there is no need to make a homemade trailer, since the scooter was originally already with a body. This body will serve not only for transporting equipment and crops, but also for people. If the tiller is equipped with a special snow shovel, then it can be used in winter for cleaning snow.
Among the wide range of choice of cultivating and motoblock equipment, I would like to highlight the tiller Ant-1 and Ant-2.
to the menu

Tiller development into more sophisticated homemade devices

A homemade tiller can serve as the basis for various more complex aggregates that can be used not only for soil cultivation. On the basis of homemade products from the “Ant” scooter, you can make a mini tractor, snow blower, towing vehicle or other mechanized device. Making a tractor from “Ant” is especially popular. To do this, a steel bar from a channel or beam is attached to the tiller frame under the engine. Then a sprung two-wheeled bogie with a seat at the top is made. The springs can be removed from the same scooter.

Under the trolley with the seat, the same rod is welded to the frame, which is connected to the tiller rod by an overhead coupling with bolted connections. This allows such a tractor from “Ant” to tow quite serious loads. The metal bar will allow the force to be distributed throughout the tractor frame. There is also a full opportunity for making a trailer for a tiller from “Ant”. 4 wheels on springs are attached to a frame made of a steel beam, and a rectangular platform made of boards or sheet metal with folding sides is mounted on top. Front side can be fitted with a driver’s seat instead of a tailgate.

You can make quite a lot of various homemade products from “Ant”. It depends primarily on technical literacy and skills in working with metal and mechanisms. In addition to the old scooter, a variety of parts and mechanisms can be used, otherwise inevitably sent to scrap metal.

Such self-made devices can radically facilitate a person’s work in a personal or summer cottage.

Their main advantage, in addition to a fairly low cost, is that they can be maximally adapted to the specific needs of the owner.

Agricultural machinery used in personal plots, fields, vegetable gardens and summer cottages, at the present time, is a fairly technologically advanced device. It is almost impossible to find a person who has not used a tiller or cultivator to facilitate the labor associated with working on the soil.

You can choose a tiller for every taste and budget, or you can make it yourself. Often the motor from the unit is used to make a full-fledged scooter, which is also indispensable for farmers, because the movement of goods over long distances is always required. Consider how to make a motor scooter Ant with an engine from a home tiller.

Use a tiller motor to give life to a new device

Homemade tiller engine and gearbox

When assembled, the tiller has a fairly compact size. In order to further reduce the overall dimensions, you can replace the parts with a muffler made by yourself from the engine. It is in essence similar to factory parts. For its manufacture it is necessary to use parts of the muffler from the “Vyatka” transport. It is important to note that the muffler is located in the exhaust cylinder bore.

READ  How To Disassemble An Engine From A Lawnmower Serving Briggs

The engine is started with a kickstarter. Each gear is shifted with a special lever mounted on the box with sectors. Control sticks with attachments hold the throttle and clutch levers. In order to integrate overrunning clutches, the gear shaft must be lengthened by about 170 millimeters. A driven sprocket is attached to the end of the left shaft.

At the moment when the shaft rotates, the clutch actively acts on the roller and also makes it move. When turning the tiller, a wheel with a large radius begins to move much faster than the immediate shaft itself. It is thanks to the factors under consideration that there are no loud and sonorous clicks during the turn.

To maintain attachments, cultivator units are used. They are welded to the channel with joints. However, before this process, they must be shortened. Longitudinal holes are attached to the tiller.

Multifunctional homemade products from the tiller engine. How to make a tiller from a motorcycle. practical tips DIY tiller from a motor scooter ant

Today tiller “Ant” can be quite serious brand-name unit of factory assembly. With its help, you can carry out various agricultural work on your personal plot, avoiding long and exhausting manual labor. At the same time, its weight is less than 100 kg, which makes it possible to transport the device in the trunk of a car. Its dimensions are quite compact, it does not require special storage conditions, it can easily fit both in a utility room and in a residential apartment in a city high-rise building. However, since the price for it starts from 25 thousand rubles, it makes clear sense to make such a tiller with your own hands from an old scooter. Especially popular are homemade tillers with an engine and a gearbox from the “Ant” scooter, which in their characteristics are close to similar factory-assembled tiller parts.

Vehicle modernization

If an old bicycle, scooter or motorcycle breaks down, you should not rent the equipment for scrap. Also, there is no need to rush to buy a new motor. It can be replaced with a power plant from a light motor cultivator. There is only 1 limitation: you cannot drive such a car on public roads. But the motor scooter Ant with a tiller engine can be used in the country for trips to the field or river. 5-6 hp engine quite enough to accelerate the moped to a speed of 50-60 km / h. Before mounting the engine on a bicycle, it is necessary to install reinforced wheels on this vehicle that can withstand a weight of up to 100 kg.

In order to assemble a scooter with a tiller engine, you will need the following tools and materials:

  • welding machine;
  • angle grinder with discs for metal;
  • electric drill;
  • wrench;
  • screwdriver;
  • pliers;
  • level;
  • hammer;
  • paint.

In order to put the power unit on the Ant, you will need to create a frame for it.

This is done in the following sequence:

  • Drawings are made, accurate calculations of the frame configuration and attachment points are made. It is recommended to check the calculations on soft aluminum strips.
  • The mounting bracket is welded. It is treated with anti-corrosion agents, bolt holes are drilled.
  • The engine is carefully mounted on the bracket and secured with bolts. The positioning accuracy is checked, the position is corrected.
  • The motor is connected to the vehicle chassis using a belt or chain. Gear shift cables, control levers are fixed.
  • Vehicle health check. The created homemade product needs to be run-in so that all the parts get used to each other. You need to spend 6-8 hours on this when the engine is running at medium speeds.

do-it-yourself ant engine tiller

Stages of assembling a tiller from a scooter

In order to assemble a tiller from a scooter, you need to disassemble the vehicle itself into its component parts. First of all, you need an engine, which must first be sorted out and put in order. Then a support frame is welded from a steel sheet with a thickness of about 4 mm and iron water pipes with a diameter of 40 mm, on which the engine is rigidly attached to three supports. After that, the carburetor, magneto, air filter and muffler are installed on the frame. To prevent the engine from overheating, a cover must be mounted above it, capable of providing forced cooling.

For a tiller from “Ant”, wheels from a scooter can be useful. They are wide enough to provide good traction. The chain drive is done with a drive that connects the motor to the shafts that have flanges that can be removed from the old combine. Gear selection can provide excellent shaft speeds, but the bottom case on the frame must be carefully dimensioned to allow the frame to reach the ground. The control is carried out using a metal telescopic tube that can be taken from a broken vacuum cleaner, which will allow you to adjust the height. The gearbox provides three positions, but only the first gear will be operational. Manual choke control.

How to install the engine from Tiller Ant

Work on installing the engine from the Tiller Ant should begin with moving the motor. Then it is recommended to adhere to a certain plan in order to get a high-quality and reliable unit:

  • Frame manufacturing. This is done by welding a sheet of iron to a 4mm diameter pipe. The frame must be firmly attached to the engine.
  • Installing the carburetor, air filter and muffler.

Important! A cooling cover must be fitted to protect the unit from overheating.

    The transmission is carried out using a chain that drives the shafts. Their speed should be different, even if the gears are correctly selected, since if it matches, the frame will not come into contact with the ground.

In this video, consider an ant on a tiller engine:

Attention! You will have to open and close the carburetor flap manually.

The unit based on the motor scooter Ant will turn out to be a little bulky, weighing about 90 kilograms, and slightly clumsy. But special maneuverability in the garden and in the field is not required, since there are usually no obstacles that must be frequently bypassed. But the motor will perfectly withstand all loads, even with long and continuous operation.

When a home-made Ant with a motor from a tiller needs to be moved a long distance, then in the manufacture of equipment it should be possible to install wheels that are bolted through, or make an additional stand for transportation in the back of a truck or in a trailer.

It is also possible to make the wheels smaller and attach a plow, potato digger or tiller.

Now the development of agricultural machinery has reached the best development. It’s hard to imagine a modern farmer without a cultivator or a tiller.

For convenient and comfortable use of the tiller, it is made from an old motor scooter Ant. On such equipment, it will be comfortable to move around the treated area, transport the fed collection, humus, agricultural tools, even firewood, garbage and everything else.

Brand Tiller Ant

First of all, you need to find an old scooter and determine what size the areas will be processed. This affects the power of the tiller motor. Motor scooter Ant with an engine from a tiller is redesigned for a real tiller according to the standard classic scheme:

  • Frame.
  • Engine.
  • Undercarriage based on 2 wheels.

Secondary parts are attached to the ts. tiller,

which, of course, will be very necessary further on using the device:

Following from the above, the necessary elements for the production of a tiller are the frame, engine, wheels, steering wheel, seat and electrical equipment. to the menu

Tiller elements are placed on the frame for our client. The frame structure consists of 2 side members, which are made of an inch and a quarter metal tube. The front and rear ends of the side members are bent upward, the rear ends must be bent towards each other, and later connected by welding. At the production stage of the control unit, the Izh bike and its parts are used.

Homemade tiller with a motor from Ant

The control structure from the bike is welded to the rear ends of the side members by welding. To tension the chain of the first stage of the box, you need to connect the side members in length with several cross members. The platform for the battery and other parts also serve as crossbars. The gearbox housing included in the frame assembly, in addition to its own functions, also makes the function of a rack between the undercarriage and the power unit. For cargo transportation by trailer, you can hook up a two-axle cart to one of the rear of the crankcase.

Reviews

Vasily, 32 years old

“The old Ant has been gathering dust in the garage for several years. After looking at several relevant articles on the Internet, I decided to adapt the motor from the tiller to it. It turned out to be an excellent au pair, an economical and reliable unit. And do-it-yourself production of Bosch would be much cheaper if I bought a new device. “.

“Combining Tiller and Ant is a great idea, which miraculously came to mind. Having made the equipment, I received a unit that perfectly copes with all agricultural work on my personal plot. It not only loosens and digs up the soil, but also helps in harvesting and transporting various heavy loads. I am very pleased with the new technology. “.

scooter tiller ant

There are more decent industrial ones, but their bite. But what about those who have almost 20 hundred square meters? The idea to make such a tiller myself came suddenly, and not to me, but to my neighbor. the artist. He came up with, and I have already finalized.

How to make a tiller with your own hands

The work began with the “Ant”, or rather the engine from the T-200 scooter. First, we iterate over. Then we make a frame. we weld an iron sheet 4 mm thick with pipes 4 cm in diameter.The frame is fixed rigidly with three supports to the engine.

The next stage of the assembly was the installation of the carburetor, magneto, air filter, muffler. In order to protect the engine from overheating, we had to come up with a cover on top for forced cooling.

The chain drive was made as a drive from the engine to the shafts with flanges (they came from a conventional combine). An important point is that the rotational speed of the shafts can be excellent with the correct selection of gears, but you still need to carefully calculate the size of the lower crankcase on the frame. If you get carried away with one frequency, the frame will simply go over the top and will not reach the ground. Gear ratio motor-gearbox 4: 1, in the gearbox 2.5: 1

Everything inside must be lubricated with oil. for this, drain and bay hatches are made.

READ  How to Make a Boat Motor From a Trimmer

As a rudder. an ordinary metal pipe (to adjust the height, you can take a telescopic pipe from an old vacuum cleaner). The unit operates in first gear, although there are already three gearboxes. The carburetor flap is manually operated. There is a wheel in front of the tiller, how deep the soil needs to be plowed depends on its installation, and it is not particularly difficult to control. The weight of the structure turned out to be decent. a little less than 90 kg.

I made the nozzles from a corner and pipes, on the shaft they are fixed with a key in a groove, so that there is no axial movement, we clamp it with a bolt. Capture width 1m. 20cm.

According to the test results, it turned out. the engine adequately withstands the passage on virgin soil, you can plow the field with the bayonet of a shovel, walking across the field 2-3 times, on previously treated soil, a second pass is not required. Due to its heavy weight, it is not very agile, but it works great in a garden where there are no bushes. When a homemade tiller needs to be moved, I insert wheels that are fastened with through bolts.

For the same unit, I planned to make a special body stand for transportation in the back, I also plan to reduce the size of the wheels and make plows, a tiller and a potato digger.

Tiller development into more sophisticated homemade devices

A homemade tiller can serve as the basis for various more complex aggregates that can be used not only for soil cultivation. On the basis of homemade products from the “Ant” scooter, you can make a mini tractor, snow blower, towing vehicle or other mechanized device. Making a tractor from “Ant” is especially popular. To do this, a steel bar from a channel or beam is attached to the tiller frame under the engine. Then a sprung two-wheeled bogie with a seat at the top is made. The springs can be removed from the same scooter.

Under the trolley with the seat, the same rod is welded to the frame, which is connected to the tiller rod by an overhead coupling with bolted connections. This allows such a tractor from “Ant” to tow quite serious loads. The metal bar will allow the force to be distributed throughout the tractor frame. There is also a full opportunity for making a trailer for a tiller from “Ant”. 4 wheels on springs are attached to a frame made of a steel beam, and a rectangular platform made of boards or sheet metal with folding sides is mounted on top. Front side can be fitted with a driver’s seat instead of a tailgate.

You can make quite a lot of various homemade products from “Ant”. It depends primarily on technical literacy and skills in working with metal and mechanisms. In addition to the old scooter, a variety of parts and mechanisms can be used, otherwise inevitably sent to scrap metal.

Such self-made devices can radically facilitate a person’s work in a personal or summer cottage.

Their main advantage, in addition to a fairly low cost, is that they can be maximally adapted to the specific needs of the owner.

Agricultural machinery used in personal plots, fields, vegetable gardens and summer cottages, at the present time, is a fairly technologically advanced device. It is almost impossible to find a person who has not used a tiller or cultivator to facilitate the labor associated with working on the soil.

You can choose a tiller for every taste and budget, or you can make it yourself. Often the motor from the unit is used to make a full-fledged scooter, which is also indispensable for farmers, because the movement of goods over long distances is always required. Consider how to make a motor scooter Ant with an engine from a home tiller.

Use a tiller motor to give life to a new device

Reviews

Vasily, 32 years old

“The old Ant has been gathering dust in the garage for several years. After looking at several relevant articles on the Internet, I decided to adapt the motor from the tiller to it. It turned out to be an excellent au pair, an economical and reliable unit. And do-it-yourself production of Bosch would be much cheaper if I bought a new device. “.

“Combining Tiller and Ant is a great idea, which miraculously came to mind. Having made the equipment, I received a unit that perfectly copes with all agricultural work on my personal plot. It not only loosens and digs up the soil, but also helps in harvesting and transporting various heavy loads. I am very pleased with the new technology. “.

Multifunctional homemade products from the tiller engine. How to make a tiller from a motorcycle. practical tips DIY tiller from a motor scooter ant

Today tiller “Ant” can be quite serious brand-name unit of factory assembly. With its help, you can carry out various agricultural work on your personal plot, avoiding long and exhausting manual labor. At the same time, its weight is less than 100 kg, which makes it possible to transport the device in the trunk of a car. Its dimensions are quite compact, it does not require special storage conditions, it can easily fit both in a utility room and in a residential apartment in a city high-rise building. However, since the price for it starts from 25 thousand rubles, it makes clear sense to make such a tiller with your own hands from an old scooter. Especially popular are homemade tillers with an engine and a gearbox from the “Ant” scooter, which in their characteristics are close to similar factory-assembled tiller parts.

How to install the engine from Tiller Ant

Work on installing the engine from the Tiller Ant should begin with moving the motor. Then it is recommended to adhere to a certain plan in order to get a high-quality and reliable unit:

  • Frame manufacturing. This is done by welding a sheet of iron to a 4mm diameter pipe. The frame must be firmly attached to the engine.
  • Installing the carburetor, air filter and muffler.

Important! A cooling cover must be fitted to protect the unit from overheating.

    The transmission is carried out using a chain that drives the shafts. Their speed should be different, even if the gears are correctly selected, since if it matches, the frame will not come into contact with the ground.

In this video, consider an ant on a tiller engine:

Attention! You will have to open and close the carburetor flap manually.

The unit based on the motor scooter Ant will turn out to be a little bulky, weighing about 90 kilograms, and slightly clumsy. But special maneuverability in the garden and in the field is not required, since there are usually no obstacles that must be frequently bypassed. But the motor will perfectly withstand all loads, even with long and continuous operation.

When a home-made Ant with a motor from a tiller needs to be moved a long distance, then in the manufacture of equipment it should be possible to install wheels that are bolted through, or make an additional stand for transportation in the back of a truck or in a trailer.

It is also possible to make the wheels smaller and attach a plow, potato digger or tiller.

Now the development of agricultural machinery has reached the best development. It’s hard to imagine a modern farmer without a cultivator or a tiller.

For convenient and comfortable use of the tiller, it is made from an old motor scooter Ant. On such equipment, it will be comfortable to move around the treated area, transport the fed collection, humus, agricultural tools, even firewood, garbage and everything else.

Brand Tiller Ant

First of all, you need to find an old scooter and determine what size the areas will be processed. This affects the power of the tiller motor. Motor scooter Ant with an engine from a tiller is redesigned for a real tiller according to the standard classic scheme:

  • Frame.
  • Engine.
  • Undercarriage based on 2 wheels.

Secondary parts are attached to the ts. tiller,

which, of course, will be very necessary further on using the device:

Following from the above, the necessary elements for the production of a tiller are the frame, engine, wheels, steering wheel, seat and electrical equipment. to the menu

Tiller elements are placed on the frame for our client. The frame structure consists of 2 side members, which are made of an inch and a quarter metal tube. The front and rear ends of the side members are bent upward, the rear ends must be bent towards each other, and later connected by welding. At the production stage of the control unit, the Izh bike and its parts are used.

Homemade tiller with a motor from Ant

The control structure from the bike is welded to the rear ends of the side members by welding. To tension the chain of the first stage of the box, you need to connect the side members in length with several cross members. The platform for the battery and other parts also serve as crossbars. The gearbox housing included in the frame assembly, in addition to its own functions, also makes the function of a rack between the undercarriage and the power unit. For cargo transportation by trailer, you can hook up a two-axle cart to one of the rear of the crankcase.

scooter with engine from tiller

At the stage of production of such a unit, a two-stroke internal combustion engine from the Ant motor scooter is used. Such an engine has forced air cooling, and such an environment is an indisputable advantage at a low speed in order to avoid overheating. The engine is interlocked with a four-stage box. To reduce the cost of the unit and reduce the size of the tiller, a muffler is performed at home,

using parts from an industrial muffler from a scooter. The exhaust tract is placed to the side, and the muffler itself is inserted into the exhaust cylinder.

The engine is started using a kickstarter, the speeds are switched using a lever located on the box with sectors. The reduction shaft must be lengthened by 170 mm in order to integrate an overrunning clutch. The driven sprocket is attached to the end of the left shaft. Due to the rotation of the shaft, the coupling interacts with the roller and the roller is set in motion. to the menu

With the help of a two-stage chain reducer, it is possible to reduce the rotation speed and increase the torque, which is transmitted from the output shaft of the unit to the rippers or wheels.

Homemade reducer for tiller

A popular solution is the use of an assembled gearbox from the Ant motor scooter. It is enough to install rollers on the bridge of the upcoming tiller, so as not to use the entire wheeled platform from the scooter. This choice of chain reducer results in a perfect balance of travel speed and tiller power. to the menu

It will be difficult to move on such a mechanism when loosening or in a snowy season if it has ordinary wheels from a scooter installed. The rippers installed on the future tiller are homemade. Wheels are selectable 5-10 inches. In order to increase the grip of the wheels with the ground, it is necessary to put on a homemade bandage on the wheels there. Such a bandage is made of a metal strip.

READ  DIY Tiller Brush

factory assembled

It is produced by the domestic industry at agricultural engineering enterprises. It is a gasoline engine on a two-wheeled platform that can both rotate the wheels of the undercarriage and drive the cutters for tillage. “Ant” is able to handle hard and virgin soil. In addition to cutters, it is possible to install a plow or a hiller on it. Four-stroke gasoline engine with 7 horsepower. This allows plowing the soil to a depth of 30 cm.The fuel tank holds up to 3.6 liters of gasoline, the crankcase volume is 0.6 liters.

The transmission is a belt drive and a chain reducer with a cast iron pulley. Forward speeds are switchable, reverse is only one speed. The engine has a manual start system. the tiller can provide a plowing width of up to 80 cm. The steering column can be adjusted both vertically and horizontally. The result is a rather powerful and easy-to-use device. The only drawback can be considered the relatively high cost, which makes the majority of owners of summer cottages and plots prefer making its analogue with their own hands. A homemade tiller will cost several times cheaper, and the consumer qualities of the mechanism will differ little from its factory-assembled counterpart.

How to make a tiller with your own hands

The work began with the “Ant”, or rather the engine from the T-200 scooter. First, we iterate over. Then we make a frame. we weld an iron sheet 4 mm thick with pipes 4 cm in diameter.The frame is fixed rigidly with three supports to the engine.

The next stage of the assembly was the installation of the carburetor, magneto, air filter, muffler. In order to protect the engine from overheating, we had to come up with a cover on top for forced cooling.

The chain drive was made as a drive from the engine to the shafts with flanges (they came from a conventional combine). An important point is that the rotational speed of the shafts can be excellent with the correct selection of gears, but you still need to carefully calculate the size of the lower crankcase on the frame. If you get carried away with one frequency, the frame will simply go over the top and will not reach the ground. Gear ratio motor-gearbox 4: 1, in the gearbox 2.5: 1

Everything inside must be lubricated with oil. for this, drain and bay hatches are made.

As a rudder. an ordinary metal pipe (to adjust the height, you can take a telescopic pipe from an old vacuum cleaner). The unit operates in first gear, although there are already three gearboxes. The carburetor flap is manually operated. There is a wheel in front of the tiller, how deep the soil needs to be plowed depends on its installation, and it is not particularly difficult to control. The weight of the structure turned out to be decent. a little less than 90 kg.

I made the nozzles from a corner and pipes, on the shaft they are fixed with a key in a groove, so that there is no axial movement, we clamp it with a bolt. Capture width 1m. 20cm.

According to the test results, it turned out that the engine adequately withstands the passage on the virgin soil, you can plow the field with the bayonet of the shovel, passing through the field 2-3 times, on previously treated soil, a second pass is not required. Due to its heavy weight, it is not very agile, but it works great in a garden where there are no bushes. When a homemade tiller needs to be moved, I insert wheels that are fastened with through bolts.

For the same unit, I planned to make a special body stand for transportation in the back, I also plan to reduce the size of the wheels and make plows, a tiller and a potato digger.

DIY motorcycle tiller video compilation

People whose budget is modest and does not give the opportunity to purchase branded awnings and attachments like to come up with various homemade products from a tiller with their own hands. In the basic configuration, this technique has limited capabilities. But even the simplest unit is an internal combustion engine that can be used as a power source for many mobile devices. On the basis of the tiller, you can also assemble stationary installations, such as a pump station, an electric generator and a mulcher.

By connecting an electric motor to the unit, you can make a universal woodworking machine. A self-made sawmill in your yard will be an excellent help on the farm.

We will make a homemade tiller with an engine from a scooter, drawings and photos

Self-handed production of a tiller with an engine from “Vyatka” of a scooter is carried out according to the traditional standard scheme:

Secondary optional parts that can also be attached to the vehicle are:

Important elements and units required for the manufacture of a direct tiller are:

Homemade tiller engine and gearbox

When assembled, the tiller has a fairly compact size. In order to further reduce the overall dimensions, you can replace the parts with a muffler made by yourself from the engine. It is in essence similar to factory parts. For its manufacture it is necessary to use parts of the muffler from the “Vyatka” transport. It is important to note that the muffler is located in the exhaust cylinder bore.

The engine is started with a kickstarter. Each gear is shifted with a special lever mounted on the box with sectors. Control sticks with attachments hold the throttle and clutch levers. In order to integrate overrunning clutches, the gear shaft must be lengthened by about 170 millimeters. A driven sprocket is attached to the end of the left shaft.

At the moment when the shaft rotates, the clutch actively acts on the roller and also makes it move. When turning the tiller, a wheel with a large radius begins to move much faster than the immediate shaft itself. It is thanks to the factors under consideration that there are no loud and sonorous clicks during the turn.

To maintain attachments, cultivator units are used. They are welded to the channel with joints. However, before this process, they must be shortened. Longitudinal holes are attached to the tiller.

Homemade tiller with a motor scooter engine “Vyatka” or “Ant

The tiller is equipped with a transmission with a mechanical gear chain structure. It has a chain, two canonical gears and two sprockets.

It is not worth complicating the structural part, since this moment can significantly complicate free maneuvering. The entire structure must use two overrunning clutches that allow the main wheels to slip.

The power unit of the tiller is a frame in which a special cross member is installed with two drilled holes with a diameter of 14.2 millimeters and a pair of holes of 12.2 millimeters. It is imperative to install two bolts numbered M12 into the inner frame part. Thanks to the approach under consideration, it is possible to freely connect the articulated knot from a cargo cart with attachments to agricultural equipment. The carrier stick is embedded on the left side of the cross member. A cut-out for the gear housing is drilled in it.

In the front of the beam, it is necessary to install a bracket support with a parking bipod.

The main bearing plate is attached to the right side. It is she who holds the direct gearbox. For the frame, it is worth using a plate with dimensions of 280208 mm. In the middle of the above plate, a special clamp is placed that secures the engine.

The front of the slab holds the vertical bar. The bracket must be welded to this rod. The chain driven from the sprocket output shaft generates fundamental torque.

Fastening tiller attachments from a scooter

Retaining brackets for locking screws and agricultural equipment are built into the ends of the rods. Special control handles with pipes are attached to the upper part of the channel. They should be flattened on both sides. For the correct installation of the lever with the steering wheel, you need to drill certain holes. Motor scooter steering shaft allows for correct manufacturing of joint assemblies.

Be sure to remember that the shaft must be shortened to about 460 millimeters. An articulated fork is welded from the bottom. The cross is attached to a metal plate. The length of these elements should not exceed 13.5 centimeters. In the lower part, the plates are carefully beveled, and subsequently welded to the same channel. Longitudinal holes will allow the cart to be tightly attached to the tiller frame. The nodes must be lubricated with a special substance, that is, with an oil can.

The Vyatka frame is perfect for the trolley frame. Angles of 3535 millimeters need to be welded to it. The same method must be used to strengthen the free endings. A half-inch pipe will allow you to connect the forks between them. The U-shaped stretcher is welded there too. It is important to note that it is made from corners with dimensions of 3535 millimeters. The body can be installed by welding the hinge sleeves.

By its very nature, a tiller is very easy to manage and transport the necessary cargo on it. The universal seat is considered a special convenience for the driver. There is also a special box with tools.

tillers have their own specific characteristics. The main ones are:

Width 670 mm;

Length 900 mm;

Height 900 mm;

The total weight is 65 kilograms;

The highest speed is equal to 18 kilometers per hour;

The length of the transport with a cart is 1580 millimeters;

The track width is 550 millimeters;

The track width with the trolley attached is equal to 750 millimeters.