Bosch electric screwdriver how to insert the drill bit. How to change a drill bit

How to take the drill out of an electric screwdriver?

Work with a screwdriver, obeying safety precautions and rules described in the manual. Choose the right tooling. And then the tool will serve you for a long time.

How to insert the drill bit into the drill and impact wrench

Often there are variants of the appearance of difficulties do not work with peoratorom another drill. In the main, the discrepancy may lie in the inability to work correctly with drills. First, let’s look at some of the differences of chucks are not drills.

How to use an electric screwdriver

Today it is difficult to imagine the repair, construction or arrangement of the house without electronic aids, one of which is an electric screwdriver. Its importance is hard to overestimate as it significantly improves the quality of work and saves time. The scope of its application. this is not only major repairs and construction work, but also various domestic situations that arise in our lives. For example, to assemble or disassemble a cabinet, change a lock, drill a hole in the wall, and much more. Let’s look at how to use an electric screwdriver.

Electric screwdrivers can be cordless or mains powered. Cordless screwdrivers are preferred because they can be easily handled without having to think about having a functioning outlet. The removable battery can be easily attached to the handle of the electric screwdriver from below and is charged via the AC adapter. It is better to choose an electric screwdriver with two batteries, it allows you to avoid long pauses in work: while one is being charged, you can work with the second one. The two most common types of batteries today are nickel-cadmium and lithium-ion. The lithium cadmium battery has a memory effect and it must be completely discharged before it can be recharged, otherwise its capacity, on which the time between charging and recharging depends, will gradually diminish.

the electric screwdriver is sold in different sets: just the tool or with a set of different bits. How to use an electric screwdriver to change a bit or insert a drill bit? bits are fastened in the three-jaw chuck of an electric screwdriver without using any other tools, but with your hands. For convenience the chuck has a rubber ribbed surface, by turning it counterclockwise we widen the chuck socket and insert the nozzle and to fix it we turn the chuck clockwise.

The electric screwdriver has an adjustment ring just behind the chuck that controls the torque speed and stops the chuck as soon as the screwdriver is screwed in. Depending on the model, an electric screwdriver has several levels of control (from 6 to 22), which allows you to choose a mode more suitable for a particular type of work and not to spoil the surface of the material. Let’s look at how to use an electric screwdriver to get the torque speed right, such as for wood. First, you set the minimum degree of control and start working if the screwdriver is not yet driven in and you hear the ratchet sound, i.e. е. If you don’t hear the engine running, you need to increase the torque. And so on, until the screw is completely embedded in the wooden surface. After that you can continue working without worrying about tearing the slot of the screw or if it will go deep. This approach allows you to work more efficiently and conserve battery power.

Scope of application of the electric screwdriver

Proper use of an electric screwdriver means using it only for the operations that the manufacturer of the product specifies in the operating instructions. The main (by designation) for this tool are such types of work:

• Screwing in or unscrewing fasteners of various types, including tightening and unscrewing bolts with nuts;
• drilling holes in various hard materials.

The use of an electric screwdriver for its intended purpose is the most common way to use this device, both at home and in construction, furniture production, electrical installation, assembly and repair of cars. The scope of application of the product is not limited to these areas: a drill electric screwdriver is useful wherever you want to work with fasteners (to assemble different structures, equipment, machinery) and drill holes of relatively small size.

The range of possible applications of a particular model is determined by the category it belongs to: household or professional. The tool, designed for home use, is relatively cheap, has low power and torque. Household models have low performance, as well as limited functionality.

Electric screwdriver from the professional category has expanded functionality and high technical indicators. Such a tool is designed for continuous, effective use for its intended purpose. Also much wider at him possibilities of unconventional use.

How to Insert the Drill in an Electric Screwdriver

How to use an electric screwdriver: step-by-step instructions

Everyone at least once for did a repair at home or did work related to the repair of their own apartment or dacha. Now an indispensable assistant in the repair is a screwdriver. Buying it, be sure to find out the power, configuration, and in addition the warranty period of the power tool.

Safety Technology

Before using the cordless screwdriver it is absolutely essential that you read the safety precautions in the leaflet that comes with the tool. It is not uncommon to use the tool in the workplace. Usually, the annotation How to use an electric screwdriver will fit in the acts of labor protection.

To prevent accidents, working with a screwdriver, our customer should obey safety regulations. Do not trust the tool to people who do not know how to use a screwdriver, and even not sure to obey safety precautions.

For example, children, old, unhealthy, and intoxicated people.

Use this equipment before wearing overalls and eyeglasses. Remember that any tool, no matter what it is, is source of danger.

How to use a screwdriver battery

Make sure your electric screwdriver’s battery is fully charged before use. Plug it into the charger and carefully study the indicator. The green battery indicator light shows that the battery is charged. The reddish color of the indicator says that it really needs to be charged.

If you set out to increase the operating time of your screwdriver, it is wise to have a 2nd battery. If the 1st battery loses power and you change it for the 2nd one, put the 1st one in the battery charger.

If the battery is charged, there is no point in keeping it in the charger. This shortens the life of the entire battery.

Also has a negative impact on the life of the battery very hot or very cool room temperature, in which the screwdriver works. The operating time of the 1st battery is 5 hours.

How to attach a bit or drill bit

To fix in a screwdriver drill bit or bit can be 2 methods. 1st method is manual. The bit is inserted into the chuck and tightened by hand. The 2nd method is to tighten the bit as it is also called a drill bit by means of a rotating chuck, hold it with the 2nd hand. It’s elementary to check how you’ve clamped the bit. Try to tighten one screw, and you will see if the bit rotates or not.

How to Insert a Drill Bit into an Electric Screwdriver?

shows you how to insert the drill correctly with your hands. Note that the techniques.

How to insert, change, and remove the drill bit with a Metabo electric screwdriver?

Shows how to properly insert and remove a drill bit from a Metabo electric screwdriver with your own hands, as well as how to.

How to properly use a screwdriver

The screwdriver has a scale on it with which you can adjust the power output directly. By turning the knob, you choose the mode you need depending on the job you intend to do. With the same dial you can also select the drilling mode.

Just don’t try to drill hard, concrete and stone surfaces with the screwdriver, so as not to put it out of order. For drilling on hard surfaces there are special tools designed for that purpose. Do not switch the control while the screwdriver is operating. Doing so could cause the tool to malfunction.

Knowing how to use the screwdriver can extend the life of the screwdriver.

Three modes of operation can be selected with a switch. Screwdriver in screwdriver mode, screwdriver in unscrewing mode, screwdriver in lockout mode. A third mode is required for safety.

All of these modes are very easy to switch if you hold the screwdriver by the handle above the battery. The handle is usually covered with a rubberized material and is therefore very safe to use.

It ensures that the screwdriver will not slip out of your hand when you need it the most. You can also strap the wrench to your hand for more security.

Drilling mode

If you want to drill holes in wood or plastic, make sure you place a straight piece of wood under the objects you are drilling to achieve a good result. This avoids cracking and chipping when drilling.

Drilling a hole in metal implies observing certain rules. The place of the hole to be drilled must be tapped out. This helps to avoid slipping of the drill bit on the metal surface.

Once you have selected the drilling mode on the screwdriver, do not forget that when drilling metal it is not uncommon for drill bits to break on the way out of the metal. To avoid that, try not to put too much pressure on the screwdriver when drilling.

If the bit gets stuck, it can be unscrewed by turning the screwdriver into unscrewing mode. If you are drilling into small pieces, use a vise to hold it in place.

Using a screwdriver

Those models of wrenches, which are sold today in stores, allow you to pick up the bit to the screw so that their adherence to each other was tight. And setting up the screwdriver so that each screw is tightened perfectly is easy.

Don’t think that you can use a screwdriver just for drilling, screwing, and unscrewing screws. You can wrench and tighten nuts and bolts, grind with a variety of surface finishes when doing repair work on your vehicle.

It is very time-consuming to assemble furniture without a screwdriver. Hanging curtain rods or bookshelves with a screwdriver is a lot easier than running around with a screwdriver and putting effort.

So now the screwdriver has taken its rightful place among the most important tools in the home.

Maintaining the tool

Timely cleaning of the screwdriver with a soft rag will prolong its life. Do not let water and moisture get on the screwdriver. Store in a dry place. Do not drop the screwdriver.

In an effort to handle the screwdriver carefully, take care also of the battery charger and its power cable. If you notice either malfunctions in the screwdriver itself or in the battery charger, try to call the service center.

How to change the nozzle on an electric screwdriver

How to use an electric screwdriver drill. Annotation. Photo.

Cordless Drill Electric Screwdriver is a tool that must necessarily be in the working set of at least any craftsman at home. Its versatility allows you to simply and easily do the work on screwing and unscrewing different types of fasteners (screws, screws, screws), and not to mention drilling holes.

Need to look at how to work drill-electric screwdriver does not understand the attachments are not devices.

Tool Set

Usually such a tool is sold in special suitcases, where each part is assigned its own craftsmanship place.

Drill itself-electric screwdriver consists of the main tool is not removable battery, which is recharged from a household electronic network.

You use a special charger that comes with the set to charge it.

To charge the battery

it is necessary to plug the battery into the device, observing the polarity (the proper signs ” ” not “-” are put on the battery, on the device), i.e.е. The plus side is aligned with the plus side and the minus side with the minus side.

The glowing reddish diode on the panel of the device indicates that the charging process is going on. This procedure takes 3 to 5 hours.

The battery is protected against overcharging, so it is an option to leave it in the device for more time, but no longer than 24 hours.

In the process of charging the battery and the device itself to be warm, which is not an indicator of malfunction.

Bits. nozzle

The electric screwdriver comes with a number of bit types with differently shaped working edges.

Bits with a straight edge are designed to work on fasteners that have a single slot (slot). Proceeding from its length and depth, you choose the right bit.

Similarly, not the shape of the cross bit is selected. here the width of the slot is not taken into account the size of the cap of the fastener itself. In order to work reliably, the bit edge must engage tightly in the slots, or else it could “stick” to the slots.

To keep the bit in the chuck a special magnetized bit holder is used which prevents the bit from falling apart and firmly holds the bit in various positions.

How to insert, change and remove the drill bit with a Metabo electric screwdriver?

This tells you how to correctly insert and remove the drill bit with your Metabo electric screwdriver, without having to do anything other than

To secure the bit and bit holder, the sliding part of the chuck must be unscrewed.

Insert the bit and not tighten the chuck completely.

There are not very comfortable double-sided bits that can be fastened in the chuck without a bit.

Torque settings

The drill has an adjusting ring for setting the torque.

This is to be able to set a more suitable value when working with materials of different hardness.

Nettle, for screwing screws into drywall (with low torque) is suitable range of values 2-4, for hardwood torque can be set to the highest digit on the ring.

This kind of adjustment helps to avoid sharp damage to the fastener’s splines.

In due course of work it is possible to change frequency of rotation, increasing or otherwise reducing force on the trigger of the tool.

It allows you to stop the tool temporarily when a screw or screws are driven in completely.

Direction of rotation of the chuck

The drill. electric screwdriver has a pusher type switch that would naturally change the direction of the chuck rotation to screw or unscrew the fastener.

There are direction indicators on both sides of the tool near the switch. Press the switch to reverse the direction of rotation.

Do not forget that you can change the direction of rotation only when the motor stops working.

Approximately the position of the switch overrides the operation of the tool. This lockout is used when changing drill bits or drills.

If you want to change the chuck of the drill/electric screwdriver. It should be taken into account that it is locked by a screw with a left hand thread does not mean that unscrew it clockwise.

Get access to this screw through the front of the chuck.

In the tool kit also comes a set of drills of different cross section. They are designed to work in relatively soft materials.

Drill bits are clamped in the chuck in the same way as the bit.(see “The switch is in the same position as the tool. photo above)

To care for the tool it is sufficient to wipe the housing with a damp cloth and then dry, do not use household chemicals not solvents.

Do not freeze the battery pack.

Tips for use with the drill. with an electric screwdriver

Before you begin, check that all parts of the tool are in good working order;

After long periods of non-use, the battery pack is still discharged, in which case it should be recharged;

It is necessary to make sure that the places of drilling do not pass the electric cable and are not laid water and gas pipes;

When working with the tool, it is necessary to avoid frequent braking of the electric motor, it can damage the battery;

Carefully check the polarity when connecting to the charger;

How to correctly insert and remove the drill bit in a peorator, electric screwdriver and drill

The popularity of the question of how to insert a drill bit in a peorator or an electric drill is explained quite simply: such devices are actively used in both industrial and domestic conditions.

There are different chucks, just like the bits that are fixed in them

Improperly installed drill can lead to a number of problematic situations:

• the inability to work with a drill bit or drill;
• The chuck is a part of its design where the drill bit shank is held in place;
• the outreach of the drill bit, which can cause serious injury.

Although it is not too difficult to insert a drill bit into a rotary tool or drill bit, it must be done responsibly.

Proper installation of the drill in the drill chuck

Before figuring out how to correctly install the drill bit in the peorator, it is advisable to find out how to insert the drill bit into the drill. The element of its design, in which the drill shank is fixed, is the chuck. Most models of modern drills have cam-type chucks, consisting of:

• the cylindrical shape of the housing;
• A ring or sleeve that rotates around the outside of the housing;
• jaws mounted on the inside of the housing.

Clockwise rotation of the sleeve causes the jaws to move in relation to each other, so that the drill bit’s shank is held securely in place.

Accordingly, the question of how to remove the drill bit from the drill is not difficult to solve: Just start turning the sleeve counterclockwise. The cams will begin to separate, allowing you to easily remove the drill from the drill.

Keep in mind that the cams should be unclamped before inserting the drill bit, so that the tool can be inserted easily.

The convenience of using cam-type chucks is not only the speed and high reliability of the tool setting, but also the fact that drills of almost any diameter can be inserted into them.

When using such chucks, there are usually no difficulties with how to change a drill bit in a drill. A correctly inserted tool is held securely in such chucks and allows you to drill precisely.

If you notice your jaws slipping when the chuck is tightened replace the wrench with a new one

Cam chucks are used in both industrial and home drilling tools. clamping devices of household drills are available for two ranges of drill diameters: from 0.8 to 10 and from 1.5 to 13 mm.

Jaw chucks can be designed with two different ways of clamping the tool: key-action and quick-action.

In the first case, the sleeve is actuated by a special wrench with teeth on the tapered working part.

To actuate the clamping mechanism, the wrench must be inserted into the holes on the side of the chuck body and rotated. There are even three such openings in some models.

Accordingly, to loosen or tighten the jaws, the wrench must be inserted in each of them and start turning counter-clockwise or clockwise.

After loosening the jaws, use the wrench to turn the chuck itself anticlockwise to increase the distance between the jaws to the required value. After inserting the tool, reverse the sequence of locking: first the chuck is locked in (clockwise rotation) and then the sockets are locked in place using the open-end wrench.

Pulling out and setting the drill bits with a quick-action chuck is considerably easier and quicker. With quick-action chucks, the shell is driven by turning it manually. To limit the pulling force of the jaws they are often equipped with locking elements.

Before you insert the drill, first make sure that the drill is in working order and de-energize it. Only then can the drill bit be inserted.

Insertion of the working tool into the peorator

As previously mentioned, the drill should be checked for proper functioning before the drill bit is inserted. To do this check, the operating mode of the lever is set to “hammerless drilling”.

When you can hear and feel the engine running smoothly and without shock after you have pressed the start button, you can use the torch for its intended purpose by inserting a drill bit or drill bit beforehand.

To fasten a drill bit with a cylindrical shank in the peorator, use an adapter with a cam-type chuck

• Place the rear part of the torch on the floor or on another hard surface.
• The sliding part of the clamping device is pulled back.
• Insert the tool into the torch as far as it will go. Keep the drill or auger inserted in the torch vertical. Should you not observe this precaution, the tool could be thrown or even broken and the tool itself could be damaged.

Press until a gap is felt, then pull the auger, if it does not come out, all is well

Considering the fact that the clamping chucks on modern rotary tools are characterized by a fairly simple principle of operation, there are usually no questions about how to remove the drill bit from the rotary tool.

After you have removed the used tool and replaced it with another one, it is advisable to clean the tool shank of grease and construction dust at once. In doing so, the shank of the drill bit that you are going to insert must also be cleaned and pre-lubricated. The tool is thus replaced without damaging the clamping mechanism of the torch and lasts much longer.

The grease extends the life of both the drill bit and the drill bit chuck

Using a peorator not only allows you to drill a structural element, but also to work with a special chisel. It is also possible to install a mixer as the working body of such a device.

Household craftsmen often have questions about how to insert a drill into an electric screwdriver or how to change the chuck on the peorator.

How to insert the drill correctly into the drill chuck

Before figuring out how to insert the drill bit into the drill, it is desirable to find out how to insert the drill bit into the drill. An element of its design, in which the shank of the drill is fixed, is the chuck. Most models of modern drills have cam-type chucks, consisting of:

• the body is cylindrical in shape;
• rings or sleeves, which rotate around the outer surface of the housing;
• of the cams mounted on the inside of the housing.

When rotating the sleeve clockwise, the jaws simultaneously approach each other, thereby securely clamping the shank of the drill bit to be installed. So, the question of how to remove the drill bit from the drill is not difficult to solve: Just start turning the sleeve counterclockwise. In this case, the cams will start to diverge, which allows you to easily remove the drill from the drill. Note that before inserting the drill bit, the cams should be unclamped, so that the tool can be easily inserted.

The convenience of using cam-type chucks is not only in the efficiency and high reliability of the tool installation, but also in the fact that drills of almost any diameter can be inserted into them. When using such chucks, there is usually no problem with how to change the drill bit in the drill. A properly inserted tool will hold securely in these chucks and allow you to drill a precise hole.

If you start to notice teeth slipping when you tighten the chuck, replace the wrench with a new one

Cam chucks are used in both industrial and domestic drilling tools. Domestic drill chucks are available in two drill diameters from 0.8 to 10 and 1.5 to 13 mm.

Jaw chucks can be designed with two different ways to clamp the tool: with a wrench and a quick-action clamping tool.

In the first case, the sleeve is actuated by a special wrench, which has teeth on the cone working part. To actuate the chuck mechanism, insert the wrench into the holes on the side of the chuck body and rotate. There can be as many as three such holes in some models. Accordingly, to loosen or tighten the cams, a wrench must be inserted in each of them and start turning counterclockwise or clockwise.

After loosening the cams with a wrench, it is necessary to turn counterclockwise the chuck itself, which will increase the distance between the cams to the required value. Inserted tool is secured in reverse order: first the chuck itself is clamped (by turning it clockwise) and then the sockets are clamped with a wrench.

Easier and quicker to remove and refit drill bits with a quick-action chuck. In it, the sleeve is actuated by turning it manually. To limit the tightening force of the jaws they are often equipped with locking elements.

Before inserting the drill, first make sure the drill is in working order and de-energize it. Only then can the drill bit be inserted.

Concrete fixtures

The size of the concrete drill bit can be different. This depends on the diameter of the hole to be obtained. But all augers for stone, brick, and similar coatings have a hard tip. It is manufactured from a special alloy that gives it higher performance. Such coatings are drilled with a twisting and tilting motion.

Whereas conventional bits have a cylindrical shank, drills for pectoral cutters also come in other shapes. Auger bits with tungsten carbide tips are used for drilling small indentations in concrete surface. Larger holes are cut with a carbide-tipped bit at the edges. Diamond sprayed tools are also popular because of their durability.

Pobedite tips are popular for granite surfaces. Such tools have different softness, so they can be used for different surfaces. For ceramic tiles, the lance-shaped drill bit with a tungsten or pobedite tip is an excellent solution. For glass, we recommend a drill bit with a special edge coating.

How to use a screwdriver correctly

The screwdriver has a scale that can be used to set the direct rotation power. Turn the knob to choose the mode you want, depending on the job you wish to do. The same knob can also be used to select the drilling mode. Just don’t try to drill into hard, concrete or masonry surfaces with the screwdriver so as not to damage it. There are specially designed tools for drilling hard surfaces. Do not switch the control while the screwdriver is operating. Doing so can cause the tool to malfunction. Knowing how to use the screwdriver can prolong its life.

Three modes of operation can be selected with a special switch. Twist mode, unscrewing mode and screwdriver lock mode. Third mode. For safety. It is very convenient to switch all these modes if you hold the screwdriver by the handle above the battery. The handle is usually covered with a rubberized material and is therefore very safe to use. It ensures that the screwdriver does not slip out of your hand at the most inappropriate moment. You can screw the screwdriver in your hand with a special strap for more reassurance.