How to cut corners of wide skirting boards

How to cut corners on a skirting board

The ceiling plinth gives an aesthetic appearance to the room after renovation. It hides all minor construction defects, gaps and crevices. Since it runs along the entire perimeter of the room, you need to be able to dock it at the corners. This is not difficult and is done in several simple ways.

How to cut the correct corner of the ceiling plinth with your own hands

You only need to cut the corners on the baguettes at an angle of forty-five degrees, which will help to combine both the outer and inner parts of the material. This can be done both through a slotted tray or in its absence by applying the necessary markings on the ceiling or on paper.

To dock fillets with a decorative corner, you need to place the corner exactly in the center between the walls to the ceiling. Attach to it on both sides of the baseboard and cut them a little with a clerical knife until they fit perfectly together.

The problem is that the standard sizes of such corners do not always fit the size of the curb, in which case it is better to cut the corner yourself.

How to cut a baguette in the corner of a wall using a machine

A miter box is a U-shaped tray with sides, in which slots are made for the cutting tool. There can be three or more slots, depending on its purpose. The slots are made in such a way as to cut parts from 15 to 135 degrees. In this case, I am interested in a simple tool with a minimum set of slots for cutting at angles of 45-90 degrees.

The tray provides a ready-made template for cutting at different angles. It can be used to trim both internal and external protrusions. In its absence, you can make it yourself. This will require four planks, even and preferably smooth. Knock the tray out of them and proceed to the holes for cutting. Mark them at 45-90 degrees, cut with a thick cutting object or circular saw.

• The ceiling plinth is applied and cut on the near inner side of the tray.
• The molding is installed in the same way as it is planned for fixing to the ceiling.
• Cutting the workpiece should only be at 90 degrees.
• The side that will be glued to the ceiling must be firmly pressed against the bottom of the tray during operation.
• The border is cut here strictly on the front side.
• For each material from which the skirting board is made, you need to choose the right cutting tool.
• It is best to start cutting fillets from the inner corner, otherwise the part may turn out to be shorter and not fill the entire length of the ceiling.

How to make an outer corner

Just as the mowing line was outlined for trimming the inner corners, the outer corners must be done. Attach the planks to the wall at the protruding corner. On the ceiling, mark a line along the length of one baguette, then a line along the other. You will get the intersection point, which should be marked on the upper parts of the skirting board. Draw the line from it to the lower edge of the workpiece (make two sides in this way).

Then work with the marked lines of the outer corner of the baguette as follows:

• Place the workpiece in the tray, pressing firmly against the front wall of the device and holding it with your hand during operation.
• Set the cutting tool at 45 degrees to the workpiece and carefully cut off the corner.
• Install the counter plinth in the same way, pressing it against the front wall of the device.
• Cut at 45 degrees, but in such a way that the angle is directly opposite to the already cut.

After all the corners have been cut off, it is required to dock the fillets together, checking for defects in the work. If there are any, remove them by carefully cutting with a knife. As for wooden curbs, the irregularities on them must be removed with a file.

Preparatory work

Before starting work, you should prepare the material with which you will have to work. Fillets are made of:

• wood;
• gypsum;
• foam;
• polyurethane;
• Pvc.

Based on this, you need to prepare the tools. Depending on the material, a device is selected that will easily cut off the part. Also, there should be glue for attaching the skirting board and a sealant to mask minor defects.

There is also special fittings for decorating corners. they are attached to the joints at the corners. Its benefit is that it can hide some of the irregularities of the work.

The higher the ceilings in the room, the wider the border should be. Otherwise, he will simply “get lost”.
Then, the surface to which the plinth will be attached is prepared. it must be dry, even and clean.

Skirting Corner Tools

Initially, you should decide what exactly to cut. If this is a light material. polystyrene, for example, polyurethane, etc., then a clerical or well-sharpened knife will do. But the most versatile tool for cutting curbs from any material is a metal hacksaw. She cuts almost everything, smoothly and quickly.

A ruler and a chalk or pencil will also come in handy, and when manually cutting a plinth, an angular ruler is required.

How to make an inner corner

• Press the fillet to the inner corner in the way it will be glued.
• With a pencil, draw the fishing line along the upper edge of the part (on the ceiling) towards the corner. Next, take the second one and press it in the same way to the second side of the wall.
• Draw the line with a pencil in the same direction towards the corner. As a result, you get the intersection of two lines on the ceiling.
• Then, reattach the skirting board on one side in the same way and mark the intersection of the lines on it. Do the same with the second baguette.

As a result, if you run the line from the mark to the bottom edge of the fillet, you get a flat line at an angle of 45 degrees.
To correctly cut the inner corner of the ceiling molding, follow these steps:

• Transfer the workpiece to the device in the same position as it will be attached to the surface and press it very tightly against the back of the tool.
• Put the hacksaw in the slots at 45 degrees to the workpiece, which must be held by hand during work so that it does not shift.
• Carefully cut the baguette, controlling the pressure of the tool, so as not to damage anything.
• Another piece of plinth should also be installed against the back of the device, also pressing and holding it tightly during operation, avoiding displacement.
• Set the hacksaw at 45 degrees to the workpiece so that it is opposite the first trimmed border.
• Cut off. Done!

It is imperative to cut off the skirting board from the front of the product so that the line is even and clear.

Inner corner

First of all, it is necessary to consider the technique of how to cut the inner corner of the ceiling plinth. After all, in any room they are. If there are no external corners in ordinary rectangular rooms, then these varieties will have to be cut in any case.

A plinth is placed on the bottom of the miter box with the side that will adjoin the ceiling. The bottom of the fillet will be pressed against the wall of the tray.

If the material is hard, it is cut with a metal saw. Soft items can be easily handled with a sharp knife. In this case, the angle should be equal to 45 degrees. If the pressure during cutting is too strong, hooks and chips will form on the plinth. An adjacent corner is cut in the same way.

Before gluing, they are applied to the wall and, if necessary, small irregularities are corrected. There should be no gaps between the skirting boards. If this is the first time this work is done, you can practice on small pieces.

General characteristics of finishing

Studying the question of how to properly cut a corner on the ceiling plinth, you should familiarize yourself with the features of such a finish. The stucco molding between the ceiling and walls is now made of artificial materials. It can be polyvinyl chloride, expanded polystyrene or polyurethane. Wood can be used from natural materials.

In the construction business, the ceiling plinth is called (scientifically) a fillet. Of all the materials from which such finishing elements are made, polyurethane is considered the highest quality. Therefore, it is better to choose it. Next, let’s try to figure out how to cut the corner of the ceiling plinth. Expert advice will help you do this job well.

Form, fittings

When studying the question of how to properly cut a corner on a ceiling plinth, you should pay attention to its shape and related products. There are embossed and smooth fillets. Their width and length can vary significantly.

When choosing the size of the skirting boards, take into account the type of interior, as well as the height of the ceilings. For a small room, where the distance from floor to ceiling is no more than 2.75 m, wide skirting boards will not work. They will look out of place. For the same reason, a narrow fillet should not be used for high ceilings. In such rooms, a 45 mm plinth looks good.

Work without a miter box

The polyurethane skirting board looks very nice in the interior. How to cut corners on such a product so as not to spoil its appearance? And here an inexperienced master will be helped by expert advice. Not always a home craftsman has at hand such a tool as a miter box. You can do without it.

For this, the markings are performed directly on the wall. First, the required length of the decorative item is measured. It is cut at right angles. Next, each detail is applied to the ceiling. Their contour is outlined with a pencil. This produces an intersection. It is applied to both skirting boards.

An inclined line is drawn from the point of intersection to the edge. This is the clipping boundary. Correct it before gluing by attaching both skirting boards to the corner. This is a fairly simple method, but even it requires a good eye and accuracy in work.

Preparatory work

To make the process quick and easy, use a tool such as a miter box. This is a U-shaped template. There are slot patterns in its side walls. They have a different angle of inclination.

There is another technique that allows you to evenly glue the ceiling plinth. Cutting corners without a miter box is possible. But still, the use of such a tool greatly facilitates the work.

First you need to mark the skirting board. If you want to create an outer corner, measure the length along the ceiling, and the inner one along the wall. For the fillet, a slope of the mowing line of 45 and 90 degrees is used. Since this is a fairly small number of slot options, it is quite possible to make a template yourself. This requires only a sheet of paper or cardboard.

If the repairer has considerable experience in carrying out such operations, he can cut corners without additional tools. The craftsman applies the fillet to the wall, and then makes notes on the product right here. After that, he cuts off the excess. An inexperienced craftsman, most likely, will not be able to cut even corners the first time. Therefore, it is better to use a miter box or close irregularities with decorative corners.

Skirting board material

Experts agree that polyurethane is the best material for the presented finishing products. But even he has a number of disadvantages. These should be taken into account before cutting corners on the skirting boards. Polyurethane is susceptible to temperature changes. Therefore, it is not used for decoration in the kitchen or bath. Otherwise, the skirting boards will quickly crack and lose their aesthetics.

Expanded polystyrene has almost all the positive characteristics inherent in polyurethane. But it is still more fragile material. It’s easy to break.

PVC skirting boards are relatively cheap. But it is very easy to leave dents or gouges on them. Therefore, work with such products should be very careful.

Wood looks very nice, but not in all interiors. In addition, it is rather difficult for a non-professional craftsman to work with such material. Do you want to make repairs with your own hands? Then you’d better still choose polyurethane or expanded polystyrene.

Outside corner

Quite often, the contour of the walls in a room has a complex shape. In this case, you will need to figure out how to cut the outer corner of the ceiling plinth. To do this, it is laid on the bottom of the miter box in the same way as in the previous version, with the side that adjoins the ceiling.

Other slots are used for these corners. They also have a slope of 45 degrees, but are on the other side. Further, after marking and trimming, 2 plinths are applied to the corresponding place on the ceiling. Adjustment in progress.

Difficulties can arise when it is necessary to cut the same skirting board on one side for the outer corner, and on the other for the inner one. Many people make a mistake here. First you need to cut the inner corner. Otherwise, a skirting board that is too shortened will not dock in any place.

Homemade tool

Don’t you have a miter box? No problem! You can do it yourself. When pruning for the first time, it is best to apply it in your work. This will require a plywood board, paper or cardboard.

Interested in how to cut the outer corner of the ceiling plinth, as well as its internal varieties, you need to take this approach into service. Draw two parallel mowing lines on the selected material. Next, using a protractor, angles of 45 degrees are made around the edges.

A homemade tool is applied to the plinth, making the appropriate notes. The pruning technique is the same. The miter box is not used if the walls in the room are very uneven. When creating an angle of 45 degrees, gaps between the joints are obtained due to such inconsistencies. Therefore, pruning is done in the previous way. Before editing, the edges must be corrected.

Applying a miter box template

To cut the plinth in the corner to the ceiling as evenly as possible, you can use a paper, cardboard or wooden template instead of a regular miter box. Two parallel mowing lines are applied to it, then a central point is found and any necessary angle is laid from it with the help of a protractor. Before you cut the corner of the ceiling plinth without a miter box, you should double-check the size of the inner or outer corners between the walls of the room, using the same protractor.

The principle of cutting corners using a template is similar to using a standard miter box. In this case, the workpiece must be pressed against the parallel mowing line and, setting the hacksaw at the desired angle, saw off the workpiece.

Marking on the ceiling for making a corner on the skirting board

There are different ways of how to correctly make a corner on a skirting board. Some are easier to do, others are more difficult. One of these methods is to mark the plinth on the ceiling. True, it is not very convenient to cut the plinth by weight, but this method is not inferior to all others in accuracy. Before cutting the plinth to the ceiling, it is applied to the surface, while all the imperfections and irregularities of the walls, as well as the size of the corners, are immediately taken into account.

Let’s consider in detail how to correctly make the corners on the ceiling plinths using this technique:

• First, two mating plinths must be cut at an angle of 90º;
• One of the blanks is pressed against the wall, and its end is abutted against the opposite wall. Then the outline of the workpiece is drawn on the ceiling.
• At the next stage, they take the second plank and press it with its butt against the wall in the same way. Outline the line.
• At the intersection of the lines obtained, a point is set, along which further trimming of the baseboards will be carried out.
• Then each of the strips is alternately applied to the ceiling again and the cutting point is transferred to the blanks.
• From this point to the corner of the plinth, a diagonal cutting line is drawn.

Using the obtained fishing lines, cut off unnecessary sections of the baseboards, then join the mating segments, checking the correctness and completeness of the fit. “How to cut a corner of a ceiling plinth. simple and correct ways”.

It should be noted that this method is more often used for internal corners.

Cutting skirting boards for ceiling decoration

Another type of ceiling plinth is made of extruded polystyrene foam. They are much denser than ordinary foam products (therefore they do not crumble), they are a little more expensive, but they are also somewhat more difficult to cut. For work, you can use the same knife or hacksaw for metal.

The most expensive skirting boards are made of polyurethane. These are elastic, strong and moisture resistant products that are very easy to cut with a construction knife. True, they cannot be used in all rooms, since polyurethane is sensitive to high temperatures. it deforms, begins to crack or crack.

For working with wooden skirting boards, only a hacksaw with fine teeth is suitable, you can use a metal tool.

How to cut a corner of a ceiling plinth. proven methods and techniques

Ceiling skirting boards are very often used for decorating rooms. They give the ceiling a complete look, allow you to convey a particular style in the interior. In addition, they serve to mask the joints between walls and ceilings, where two different materials are mated. Although not always such elements are present in the premises, they make the interior more complete. In the material below, we will tell you in detail how to cut the corner of the ceiling plinth, since in such places the joining of individual elements is often a problem for inexperienced builders.

If the room has a simple shape, then only the inner corners will need to be cut. But in rooms of a more complex configuration, with columns, partitions and niches, there will also be external corners. For decorative elements to look beautiful, trimming must be done correctly and accurately, otherwise the appearance of the ceiling will be spoiled.

To trim the ceiling plinth in the corners as best as possible, you can use quality and sharp tools or other means. The type of tool that will be used to cut skirting boards depends on the type of material used to make them. So, ceiling plinths are made of PVC, foam, polyurethane and wood.

The cheapest option is PVC skirting boards. They are soft, so it is easy to leave dents and creases on them, which cannot be fixed in any way. In addition, this material has the ability to attract dust. A hacksaw or a sharp knife is suitable for cutting such skirting boards.

Another fairly cheap type of material is polystyrene foam skirting boards. They crumble easily, so only a sharp knife or a metal hacksaw should be used to trim the corners of the ceiling plinth. Movements should be soft, without pressure.

Using a miter box to cut skirting boards

In carpentry, a special device made of wood, metal or plastic is often used. a miter box. Special cuts are made in it, which allow an even cut at 90º, 45º, and in more complex devices. even at 60º. There are also professional miter boxes equipped with a swivel mechanism. In them, the cutting tool can be installed and fixed at any angle to the workpiece. Before making a ceiling plinth in the corners, you need to understand the details.

To cut the inner corner of a ceiling plinth using a miter box, you must:

• First, the skirting board must be attached to the ceiling surface and mark the length.
• Now a piece of plinth is placed in the miter box in the same position as it should be placed on the ceiling.
• The plinth is tightly pressed against the back wall of the miter box.
• Hold the work piece with one hand to keep it from shifting while cutting.
• The hacksaw is set at an angle of 45º to the workpiece.
• Cut the plinth, controlling the degree of pressure of the hacksaw, so as not to damage the product.
• Then proceed to cutting the counter piece of the skirting board. It is also applied to the far wall of the miter box.
• The workpiece is pressed and held by hand so that it does not move.
• The hacksaw is installed at an angle of 45º to the workpiece so that the direction of the cut is opposite to the first element of the plinth.
• Cut off the corner of the plinth.

After trimming the ceiling plinths in the corners, they proceed to the joining of the resulting elements. If the cutting was carried out accurately, they will fit snugly together.

Please note that it is recommended to start cutting the inner corner of the skirting board from the front side. Then the cut line will be more accurate and even. As for the wooden elements, then all the flaws on them will need to be cleaned up with a file. “How to properly cut the ceiling plinth in the corners. options and methods for plinths from different materials”.

Let’s take a look at how to cut the outer corner of a ceiling plinth using a miter box:

• It is best to start marking and measuring the ceiling plinth from the inner corner, and only after completing it, start cutting the outer corner. Otherwise, the plank may be short, not enough to fill the entire length of the ceiling.
• The plinth is applied to the ceiling and its length is marked.
• Then the workpiece is placed in a miter box and pressed against the front wall.
• The hacksaw is placed at an angle of 45º and, holding the workpiece with your hand, saw off the corner.
• Similarly, you must cut off the opposite part of the outer corner.
• The workpiece is pressed against the front of the miter box.
• The hacksaw is placed at an angle of 45º to the plinth and the workpiece is sawn off.

At the end of the work, the pieces of the skirting board are joined together, checking if everything is done correctly and evenly.

It should be noted that the miter box can help to cut the corner of the ceiling plinth as evenly as possible only if the walls are strictly perpendicular. If they are uneven and the angles are not accurate, this device is unlikely to be useful. “How to properly cut the corner of the ceiling plinth. rules and methods”.

How to make a miter box yourself

Often the only way to cut the corner of the ceiling plinth evenly is to use special tools so that the tool does not move to the side during the cutting process. In this case, you can make a miter box yourself.

Option 1. A box in the shape of the letter P is made of three boards. The required corners are marked on the walls of the box and the slots are cut out in the appropriate places. The result is a complete adaptation.

Option 2. Sometimes it is quite difficult to make the corners of the skirting boards on the ceiling as even as possible, especially if you have to keep the workpiece by weight. In this case, you can use a homemade device. Take two boards and knock them down in the shape of a corner. Then, on a sheet of paper or cardboard, they draw a mowing line with the desired angles, apply a template to the corner. Then the plinth is pressed, a template is placed under the cutting site and the corner is sawn off along the lines.

Option 3. If you are still in doubt about how to properly cut the corner of the skirting board, almost any household item, the shape of which allows you to form a corner, can help with this. It can be a chair or a table, just set against the wall.

To understand how to properly cut the ceiling plinth, you should also familiarize yourself with the rule for measuring blanks. So, to complete the inner corner, the length begins to measure right from the beginning of the corner. But to determine the outer corner, it should be borne in mind that it will be issued into the space of the room by the amount of the width of the product.

There is no need to rush and fix the workpieces before the mating skirting boards have been made in the corner. In order not to redo the work, you must first make sure that the mating surfaces are tightly adjacent to each other and to the ceiling. Small flaws can be corrected with a file, a thin nail file or a knife, depending on the material of the products.

If cutting off the skirting boards in the corners did not work out perfectly, small gaps can be simply putty. In general, the process of trimming skirting boards in the corners is not at all difficult. However, for training, you can take a few small pieces of the baseboard and practice on them.

The need to trim skirting boards

Installation of ceiling plinths (also called fillets) must be carried out using the correct technology. However, there are no difficulties in it. the vast majority of fillets are mounted with glue. It is enough just to properly coat the product and hold it in the right place for a while.

But with how to properly cut the ceiling plinth in the corners, questions arise. When arranging a ceiling, there is always a need to process corners. but their value can have both a standard value (for example, a right angle) or a certain deviation. The latter case is possible if the room has a complex shape, or if during the repair it was not possible to align it.

The fillets should fit perfectly evenly, regardless of the corners of the room. In addition, skirting boards often have to be cut at the outer corners. To carry out such work correctly, you need to stock up on the right tools and figure out how to cut the corners of the ceiling plinth at home.

Cutting skirting boards for ceilings without miter box

You also need to figure out how to glue the ceiling plinth without a miter box. this tool is far from always available. One of these methods involves marking the skirting boards on the ceiling. Perhaps the only drawback of this method is the fact that it is not very convenient to keep the bar motionless while applying the markings. Otherwise, the method is quite reliable. the measurement accuracy is higher, since when the plinth is applied to the place, all errors become noticeable.

Another method is associated with corner trimming of the plinth. The edges of the two joining workpieces are cut at right angles. One of the planks is applied directly to the corner, after which a fishing line is applied to the ceiling along the contour of the plinth. The same operation is repeated with the opposite skirting board.

The point at which two separate mowing lines intersect is the point where the skirting board will need to be cut. The workpieces are again applied to their places in turn, the cut mowing line is marked on them. A straight line is drawn from the mark to the opposite edge of the part. The skirting boards are cut in accordance with the markings applied to them and are joined in place. This method is an excellent answer to the question of how to connect the corners of the ceiling plinth without a miter box, especially when it comes to internal corners.

Features of cutting different materials

The following materials are used for the manufacture of ceiling plinths:

• Styrofoam;
• Wood;
• Expanded polystyrene;
• Polyurethane.

Each option has a number of characteristics, so they need to be considered separately.

Inner corner cutting

The inner corner cutting technology is as follows:

• The first step is to attach the baseboard to the ceiling. The required length is set on the plinth.
• The skirting board is inserted into the miter box in the same way as it will subsequently be located on the ceiling. The part is pressed against the far wall of the miter box and held in a stationary position.
• The hacksaw is positioned in the slots that mark the 45-degree angle. The workpiece laid in the miter box can be cut, and the effort required for this is minimal. you should not press too hard on the hacksaw.
• Now you need to cut off the opposite plank. The operation itself will be carried out in the same way, only the plinth must be placed not at the near wall of the miter box, but at the far one, so that the corners can be joined in the future.
• The cut skirting boards must be joined together to make sure the cut is correct. When cutting internal corners, it is recommended to start work from the outside of the product. After work, it is advisable to slightly adjust the cuts with a file in order to improve the quality of the joint.

Finished corner pieces

Unfortunately, this method is not relevant in all situations. The dimensions of the corners produced at the factory are adjusted to certain standards. but the skirting boards themselves do not always meet the standards. Of course, such details can be combined, but the result will look unaesthetic. If corners of a suitable size are not on sale, then you will still have to cut the baseboards yourself.

Polyurethane

Polyurethane skirting boards are the most expensive products. The high cost is due to a large number of advantages, among which are excellent resistance to moisture, high mechanical strength, reliability and elasticity. For most situations, this option will be optimal.

However, there are exceptions. polyurethane does not withstand temperature extremes. If you place such skirting boards in the kitchen near the stove, then over time, the polyurethane will deform and crack. Cutting of such fillets is performed with a special knife, and no complications arise in the process of work.

Wood

Wooden ceiling skirting boards differ from analogues. Wood has a fairly large weight, which affects the mass of products from it. As a result, the skirting boards turn out to be quite dense, very resistant to mechanical damage and hard, which allows you not to be afraid of accidental deformation during installation or cutting.

To trim a fillet made of wood, it is best to use a fine-toothed hacksaw designed specifically for delicate work with this material. However, a good option would be a high-quality sheet for metal.

Necessary materials

The set of tools for making a corner ceiling joint without using a miter box is not so great, and, in principle, does not differ from a set with a miter box. Almost every home has these tools:

• pencil;
• roulette;
• ruler;
• construction knife with replaceable blades;
• hacksaw;
• ceiling plinth.

You will need a tape measure and a ruler for accurate measurements and drawing straight lines, everyone has them in the house. It should be borne in mind that without a ruler, you will not be able to draw even mowing lines for cutting corners using the first method.

A construction or office knife with replaceable blades is an indispensable assistant in the house. Its cost, like a construction pencil, is low, and it is always available, it will give you the opportunity to cut off the necessary segments easily and evenly, cut out a corner or cut thin plates when adjusting the connection. Some skirting boards are made from a material that is recommended to be cut with a knife only, and not with a hacksaw due to the softness of the material.

You will only need a hacksaw if the material from which the baguettes are made is recommended to be cut only with it. A regular hacksaw with fine teeth will do.

A ceiling plinth must be chosen for both aesthetic and practical reasons. It should harmoniously fit into your design, cover the joints of the ceiling and walls, hide defects and irregularities. When choosing a baguette, it is necessary to take into account the material from which it is made. this affects the choice of cutting tools and glue for installation, as well as the type of coating on which the skirting board will be glued.

Step-by-step instruction

When installing a ceiling plinth, first of all, you need to prepare the surface before gluing the plinth, it must be cleaned of minor irregularities, then you need to prime the gluing points to create maximum adhesion between the glue and the wall or ceiling. The primer is the same as that used for wallpapering or ceiling tiles.

Before gluing, it is recommended to take a small piece of baguette and practice cutting out corner joints so as not to spoil the excess.

So, you have everything ready, and it’s time to start the process of cutting out the corners. To create an inner corner, the first of the methods described above is perfect for you. If you have smooth walls, you can cut off equal pieces from the baguettes, and cut out corner joints from them, then simply gluing long strips carefully point-blank to them. These manipulations will facilitate your work when trimming and exclude the possibility of bending the baguette or breaking it.

If the walls have flaws, and you are worried that the gluing place will then be noticeable, you can adjust the corner on the floor, and then glue.

When cutting out the outer corner, it must be remembered that the inner corner rests against the wall, and the outer one, on the contrary, protrudes above it. Similar to the method described in the first method, you can try. The only difference will be that the skirting board should go beyond the wall to the width of your baguette plank. After trimming the planks to the desired angle and connecting them, you may need to manually correct the angle, since the angles in our homes are often not nearly 90 degrees. The rest of the methods described by us will allow you to more easily make the outer corner. Just like cutting the inner corner, it’s best to practice first. this will make your job easier and reduce skirting waste.

Before gluing the skirting boards, you need to make sure that the joints fit exactly. Modern assembly adhesives set very quickly, so you will have practically no time to correct the mistake, and tearing off the skirting board is both an opportunity to break it and the need to re-clean the surface of the skirting board and the wall from glue. It is better to remove excess glue immediately with a small clean rag or sponge so that there are no traces left.

With the right patience and the right fit, you can achieve a ‘seamless’ joint and your molding will look solid, making it easier to paint and eliminating the need for a finishing putty to smooth joint seams.

How to make a corner on a skirting board without a miter box?

The ways

There are two most common methods for cutting flawless skirting corners correctly, easily and comfortably. The first implies the purchase of a special miter box with a large number of cuts along its perimeter, which help to cut the corner correctly and evenly. The second option is cutting corners without the help of a miter box, which we will talk about today. This process for beginners is quite complicated and painstaking, besides, the presence of a miter box does not guarantee 100% facilitation of this work, be prepared for the fact that the first time you may not succeed.

There are several ways to create corner joints without using a miter box.

One of them is the marking directly on the ceiling. To get started, we need two pieces of baguette cut at a 90 degree angle. It is not necessary to take two-meter slats at once and try to cut them, you can cut off two pieces of 15-20 cm for easier holding with one hand in the position you need. Next, we apply them in the next order to the ceiling and draw a 5-centimeter line along the ceiling to the end of the baguette, pressing the plinth tightly. After that, we apply a second molding to the opposite corner, and do a similar action, and at the intersection of the baguette and the previously held mowing line, we make a neat pencil notch on the baguette. With the second plinth, you need to repeat the same thing, making a similar notch at the intersection of the baguette and the mowing line.

Now we can cut the baguette at the angle we need, for this, use a construction knife or a hacksaw, depending on the material from which the skirting boards are made (below we will tell you what materials the baguettes are made of and what is better to cut them). To cut the corner correctly, place the baseboard on the table or chair, and cut from the point you marked on the ceiling to the opposite corner of the baseboard. After that, you can easily join the corners and glue. It should be borne in mind that this method is suitable for fitting only the inner corners, it will not work to fit the outer corners.

The second method consists in tracing a sheet of paper or plywood under the miter box, for this you need to draw two parallel mowing lines, then draw a perpendicular from one mowing line to the other, so we get a marking for a right angle. To mark at 45 degrees, you must use a clerical triangle or a protractor, passing two mowing lines through the perpendicular at 45 degrees relative to parallel lines. Further, as when working with a miter box, we put our plinth along the mowing line and cut at the required angle.

It should be borne in mind that this method does not guarantee you an ideal angle, and, in general, in our houses the corners are uneven. “filled up”, and therefore you will have to adjust the angle manually later.

The third method is to make a primitive miter box with your own hands, which is why it will not become less effective. To do this, take three planks or planks and knock them down in the shape of the letter “P”, make slots at right angles and two slots at 45 degrees. This way you cut corners without the “help” of the chair.

The fourth method is quite rare and inventive. it consists of tricks with thick paper or cardboard and a small bar. To do this, bend a sheet of cardboard at the angle you need, take a small block, which will serve as a template for cutting the corner. Press the prepared sheet of cardboard to it and, holding the knife or hacksaw strictly vertically, carefully cut the block at the angle you need. To trim the skirting board, simply place the piece on top of the skirting board, press firmly and cut along the mowing line of the piece.

The fifth way is the purchase of special fittings with ready-made ceiling corners: internal and external. Unfortunately, there are a lot of skirting board design variations; special inserts may not be found under your skirting board. But in general, it is very convenient for those who do not want to engage in cutting out corner joints.

But also if there are non-standard angles in your house, then ready-made blanks or a miter box will not help you. After all, there are only 45, 60 and 90 degrees you can cut the connection. In this case, cut the edge of the baguette by eye at an angle of 45 degrees, and when trying on to your corner, carefully trim it, so you will be able to achieve an almost perfect connection, with only one thing. there can be a lot of such fittings and trims.

As you can see, in the absence of a miter box, you can still cut the correct corner joint for baguettes, you just need patience and perseverance, and unnecessary skills will not interfere with anyone in the future.

Sometimes the unevenness of the walls or ceiling prevents you from gluing the plinth along its entire length, tightly pressed against the wall or ceiling, or you made a little mistake when cutting the inner corner, and you have a gap. To eliminate these defects, a white acrylic finishing putty is perfect. It can be painted well after drying, and with its help you can gently putty the joints. This putty is sold in a ready-made form, you do not need to stir it yourself with water and worry about non-compliance with the proportions, depending on the manufacturer. If you want to make everything aesthetically pleasing, then spare the money and buy a small jar. According to personal observations, 0.5 kg cans of ready-made putty will be enough for you both for all the flaws in the joints of the ceiling plinth, and for eliminating other minor errors during the repair.

And also for easier trimming of corners, you can use a clerical triangle, it will give you the ability to accurately cut a 45-degree angle.