How to remove the coil from a Patriot grass trimmer

trimmer erletrichesky for grass Patriot ET 1000 How to Remove the Reel

If your reel is designed to work with only one tendril, then it is simple. You need to unwind 2-4 m of fishing line (depending on the size of the spool), find a hole on the inside of the spool fixing the line for the trimmer, insert one end of the line there and start winding the line for the trimmer in the direction opposite to the direction of rotation of the spool on the trimmer. On the inside of the spool usually indicate with an arrow in which direction to wind the line for the trimmer. After winding the line for the trimmer, leave a small piece of it unreeled to expose it to the outside. This piece is fixed in a special groove, located on the same inside of the spool and is designed to ensure that at the time of gathering the spool the line for the trimmer is not unwound. If there is no such groove, you have to hold the line for the trimmer with your finger to prevent it from unwinding during the further assembly of the spool. Next, take the outer part of the spool and pass the outer piece of fishing line through the existing hole, assemble and put the spool back on the grass trimmer.

If the spool is designed to work with two tendrils, then do the following. On the inside of the spool, see how many grooves there are for winding the line. There may be one or two. If there is one groove, it means that both tendrils are wound along this one groove. If there are two grooves, each tendril winds in its own groove. A reel with one groove should have a through hole, into which the line for the trimmer is threaded. Unwind 2-4 m of fishing line, put it through the hole so that the line would stick out equally on each side. And wind both tendrils of fishing line simultaneously in the same direction, opposite to the direction of rotation of the spool on the trimmer and coinciding with the direction indicated by the arrow on the inner part of the spool. Leave some line unreeled, fix the ends of the line in special grooves, and if they are not present, hold them with fingers. Slide both ends into the available holes on the outer casing of the spool. Assemble the spool and fasten it to the trimmer.

If there are two grooves, a piece of line length of 2-4 m fold in half, the resulting place of the bend loop put into the groove that is between the two grooves, and wind both ends of the line at the same time, each in its groove. Further actions are similar to the previous version.

There are also spools where the line for the trimmer is threaded through a through hole on the inside. After that, the ends of the fishing line, without winding, are fed completely through the holes on the outer casing of the spool, collect the spool and begin to rotate the button, which is usually pressed, in order to release the line for the trimmer during operation as it wears out. If you turn the button, the trimmer line winds up inside the trimmer. It is not possible to turn it in the “wrong” direction, because it can only turn in one direction. If you get used to it, you can reel the line for the trimmer on such a spool, even without taking it apart. you just need to align the through hole of the inner reel with the holes on the outer casing of the spool, and then put the line for the trimmer through them.

That’s all on the subject. Good winding!

Is it possible to make a spool on the grass trimmer with their own hands

There are a large number of trimmer heads on sale (not automatic), which are inexpensive and of good quality. But sometimes there are situations, for example, in the country, when the trimmer reel is broken, and its repair is impossible, the store is far away, and it is necessary to mow. In this case, you can quickly, literally in a few minutes, to make a simple trimmer attachment for fixing the line from ordinary plywood 10-12 mm thick.

• Take a piece of plywood or textolite and draw a circle about 14 cm in diameter on it.
• Cut the disk with a jigsaw or metal saw.
• Drill a hole in the center of the disk matching the diameter of the reducer shaft. Do not forget to put a washer on the disc before mounting it on the shaft.
• Around the edge of the disc you can screw in small corners or make 1-2 holes on opposite sides. They will serve for threading the fishing line into them.
• To fix the line for the trimmer you can screw a few screws into the plywood.

Such a home-made mowing head is attached to the shaft with a nut. There is no way to tighten or loosen the nut without locking the shaft. To replace the cord, all you have to do is let go of the screws, insert a section of fishing line of the desired length, and press it down again.

It is also possible to make a mowing head out of metal sheet to attach a fishing line to it. How to do it, you can understand from the following video.

What kinds of lines are available?

A common type of line that fits on virtually all types of spools is cord with a circular cross section. This is a common line for trimmers, applicable to mowing succulent grass, but it will be much harder to mow dead wood, much less to cope with shrubs.

Usually, the cross section, with which you can mow young grass, does not exceed 1.6 mm. The thicker the thread, the rougher the grass it can overcome.

There is a line with sharpened facets in the form of a star or a square, this option is more adapted to mow dry grass just by having a sharp edge, but the disadvantage is its greater wear and tear, and on the strength it concedes round cord.

There are lines with improved aerodynamics with appropriate dents, scales and notches, a similar product makes less noise, but use it only on benzokosa, since the output of such thread from the spool is difficult, using it in most cases with discs, which are inserted segments. The disadvantage of such a product is its fragility.

In most cases, gasoline trimmers with engines over 1.5 liters.с. use cords with an iron cable inside. How to disassemble the spool how to replace the head trimmer for grass with a cutting blade video. How. Such a cord is perfectly suitable for mowing dry grass and small shrubs. How to Disassemble a Grass Trimmer Head How to Disassemble a Grass Trimmer Head. Answer the spool with. The presence of the core, positively affects the durability of this material. The disadvantage of such a cord is its price, which is significantly higher than the above-listed opponents.

How to thread a trimmer line into a grass trimmer reel

It takes about 10-15 minutes to wind the fishing line for the trimmer. What is a grass trimmer reel? A plastic body with a cassette inside, which has a special hook for easy winding of the fishing line. The structure of the grass trimmer reel and its main faults. How to remove the spool from the grass trimmer, disassemble it, change the fishing line for the trimmer and install it back. Almost all trimmer reels have a similar attachment principle, this is the central screw-button, when you click on it, it is possible to pull the line for the trimmer of the required length. The photo below shows several examples of different trimmer reels.

Bobbins trimmers, the motor of which is located near the ground, have a different attachment to the axis of rotation, they have on the spool two buttons located on the sides, which should be pressed, otherwise the replacement thread is no different from other cassettes.

The principle of winding the line correctly is the same in all the above cases, so let’s take the standard version with two tendrils as an example.

To remove the spool with a fishing line it is necessary to unscrew the screw, located in the center, but note that the thread there is left, so you have to turn it clockwise, this is done on purpose, so that during operation it will not open under the influence of centrifugal force.

Next, using a screwdriver, dismantle the head and remove the spool, which is directly wound on the line for a trimmer. Having measured the necessary length and having folded in half, it is necessary to tuck a fishing line for a trimmer in a reel, having deduced, as a result, its ends opposite to each other (for this purpose there are special slots for fixing).

The head is then reassembled in the reverse order by inserting the ends of the filament through the two appropriate holes.

If there are doubts or it is not quite clear how to charge the line for the trimmer on the grass trimmer we recommend to see how to correctly wind the line for the trimmer in the lawnmower. In this video, a step-by-step instructor will uncoil the trimmer head in detail, measure the amount of fishing line needed, usually two to four meters, and demonstrate the assembly and installation on the grass trimmer.

How to tuck the line for trimmer into the grass trimmer spool

It takes about 10-15 minutes to coil the line for the trimmer. What is a grass trimmer reel?? Plastic body with a cassette inside that has a special hook for easy winding of fishing line. The device of grass trimmer reel and its main faults. How to remove the spool from the grass trimmer, disassemble it, change the fishing line for the trimmer and install it back. Almost all trimmer reels have a similar attachment principle, this is the central screw-button, when you click on it, it is possible to pull the line for the trimmer of the required length. The photo below shows several examples of different trimmer spools.

Bobbins of trimmers, the motor of which is at the ground, have a different attachment to the axis of rotation, they have two buttons on the spool, located on the sides, which must be released, otherwise, the change of thread does not differ from other cassettes.

The principle of the correct winding of the line is similar in all of the above cases, so for example let’s consider the standard version with two tendrils.

To remove the spool with a fishing line it is necessary to unscrew the screw, located in the center, but note the thread is left, so you have to twist clockwise, this is done on purpose, so that during operation it is not opened under the influence of centrifugal force.

Next, using a screwdriver, dismantle the head and take out the spool, which is directly wound into a line for the trimmer. Measuring the required length and folded in half, you need to tuck the line for the trimmer into the spool, bringing, as a result, its ends opposite each other (for this there are special slots for fixing).

The head should be reassembled in the reverse order by inserting the filament through the two holes in the head.

If there are any doubts or it is not quite clear how to charge the line for trimmer on the grass trimmer, we recommend to see how to wind up the line for trimmer in the lawnmower correctly. In this video the instructor will show in detail step by step the trimmer head, measure the necessary amount of line, usually two to four meters, and demonstrate the assembly and installation on the grass trimmer.

Strand change on trimmer

If the light impact of the button on the grass trimmer spool on the ground line trimmer is not extended, the conditions for this happen next.

Variant 1. jamming occurs, t.е. The filament is caught between coils. This miscommunication usually occurs if the user has wound the line for trimmer on the reel unevenly, with crossed turns, or wound it with insufficient tension. In the latter case, when the mowing head rotates at great speeds the cord begins to tighten under the influence of centrifugal force, under the influence of which you intertwine the fishing line. To fix the problem it will be necessary to disassemble the spool on the trimmer and rewind the cord correctly, in other words, by even turns with a good tension.

Option 2.7. very long ends protrude from the head. The line for the trimmer may not come out when hitting the ground, if its ends sticking out of the head are not long enough (not long enough). There is not enough centrifugal force to cause the trimmer line to stretch. Because it is required to suspend the unit (turn off the engine as it is also called disconnect trimmer elektrichesky for grass from the network) and pull the line for the trimmer manually, having previously pressed the button.

Variant 3. A line for the trimmer is soldered inside the mowing head. This leads to a mowing head that is blocked and does not even spin when the button is pressed. In general, this occurs for several reasons: poor quality cord, overheating of the spool during prolonged use of the machine, the impact of the line on solid objects.

• At the beginning the cords of other manufacturers you will like the cords are made of low quality and easily fusible materials that do not withstand the mechanical and thermal loads. You should therefore give preference to “branded” lines.
• If you still caught line for trimmer unknown properties, and it often soldered at the time of operation, it is possible to follow the example of some users, who, after filling the cord in the coil lubricate it or silicone grease (from the canister), or mineral oil. This procedure greatly reduces the possibility of soldering between the coils of line.
• Also, the line for the trimmer can meld if, while mowing, it bumps into a hard object (a rock, a fence, a dry branch, etc.) and the line.д.). Once this is done, it is stretched a little and pulled back into the head at high speed. Friction causes the filament to warm and the coils to stick together. The only thing to do to eliminate this malfunction is to open the grass trimmer spool and rewind the line for the trimmer.

A string mower head is one type of executive mechanism of a garden grass trimmer. It is designed for mowing grass and represents a special spool (spool), from which the cutting cord (string, line for trimmer) stick out in different directions. String is a consumable material that must be replaced during use. Based on the design and operational features of the grass trimmer, manufacturers equip their products with a variety of types of heads. from simple manual reels to complex automatic reels. The more complex the device of this mechanism, the more likely its breakdowns. What to do if the coil does not spin, the string does not feed or breaks, as well as with other malfunctions. in the material below.

Grass trimmer reel design

String mower heads for trimmers are available in many designs. Both simple and complex. The illustration below shows the semi-automatic trimmer head from a Husqvarna disassembled mower (Husqvarna).

This type of head is present in the configuration of most gas mowers and electric trimmers, such as STIHL (Stihl), Patriot (Patriot), Champion (Champion), Bosch (Bosch), Huter (Huter) and others. The mower head is quite simple. It consists of the following parts:

• Mowing Head Base;
• A button for the semi-automatic cord feed;
• The reel (spool), which is filled with fishing line;
• Spring;
• Eyes. The trimmer line comes out through them;
• Grass trimmer head cover;
• Trimmer line (cord).

The following photo also shows the simpler grass trimmer heads.

All of these attachments do not allow you to change the length of the mowing line in semi-automatic mode (after pressing a button). In case of cord breakage, mower must be stopped and replaced manually.

Device of a trimmer coil for grass

Mower heads for trimmers are available in many designs. Both simple and complex. The picture below shows a semi-automatic trimmer head from a Husqvarna mower disassembled (Husqvarna).

This type of head is present in the configuration of most gas mowers and electric trimmers such as STIHL (Stihl), Patriot (Patriot), Champion (Champion), Bosch (Bosch), Huter (Huter) and others. The mower head is quite simple. It consists of the following parts:

• Mowing the base of the head;
• Button for semi-automatic cord feed;
• The reel (spool), which is filled with fishing line;
• Spring;
• Eyes. The line for the trimmer comes out through them;
• Grass trimmer head cover;
• line for trimmer (cord).

The next picture also shows simpler grass trimmer heads.

All of these attachments do not allow you to change the length of the mowing line in semi-automatic mode (after pressing a button). In the case of cord breakage, the lawnmower must be stopped and replaced manually.

Trimmer heads: types and principle of action

Domestic market offers owners of trimmers reel several types: manual, semi-automatic, automatic and universal. They differ from each other both in the way they feed the fishing line and the principle of charging it. Winding the line for the trimmer is also possible in different ways. According to this principle, spools are classified as quick-loading and collapsible.

Before you buy a grass trimmer and / or buy spare spools for it, you should always familiarize yourself with what kind of consumables are suitable for a particular model. This is important because the spools from different manufacturers may differ not only in the feeding and threading methods of the cord, but also in the attachment axis, thread type, and the diameter of the line used. For example:

• Mounting axis can be fixed (fixed) or rotating 90 °, 180 ° or 360 °;
• for low-power trimmers is suitable trimmer line with a diameter of 1.3 to 1.6 mm, and for more productive. up to 2.0 mm
• professional grass trimmers are usually equipped with universal heads with a cutting cord diameter of 2.5 to 4.0 mm.

Tip! Specialists recommend using string heads equipped with ball bearings, as they have a longer service life, while reducing the wear and tear of the incoming components. At the same time for replacement, it is best to choose a reel of that manufacturer, which is specified in the operating manual of the grass trimmer, which in turn will allow you to properly install the head on its drive.

Reels with manual control

Manual mowing head is a spool, in which the cutting cord is pulled by the grass trimmer owner himself when worn. To do this, turn off the tool, remove the head and use your hands to pull the trimmer line to the desired length. However, despite some inconveniences, this type of head is considered the most reliable.

How to repair a spinning reel

Modern technological rod, whether it is a spinning rod or a float fishing rod, is necessarily equipped with one type of reel. Most often this element of equipment is a gearless spool, simple in operation and democratic in price parameter variant. When buying a mechanism, an angler counts on the longevity of use of the product with the lowest costs for its maintenance. But one way or another, sometimes we have to deal with some malfunctions of the device, which in most cases can be repaired independently, without resorting to the services of professional craftsmen, thus saving both time and money, as a result having confidence in the debugged work of the mechanism.

To the reader’s attention we will present a number of minor mishaps that can happen to winch during its operation, but such failures are quite able to fix any little-known with the locksmith works fisherman.

How to refill your trimmer line in a grass trimmer reel

It takes about 10 to 15 minutes to rewind the mowing line. What this reel looks like

Grass trimmers? Plastic case with a cassette inside that has a special hook for easy winding. Virtually all trimmer reels have the same mounting principle, this is a central screw button, when pressed it becomes possible to pull the line for the trimmer of the desired length. Video replacing fishing line in the trimmer; How to wind the fishing line on the brushcutter? Video on line replacement in trimmer and line winding on mower. How to remove the spool, disassemble the spool on your trimmer and unscrew the nut without. The photo below shows some examples of different trimmer reels.

Preparing to change the line

Before replacing the fishing line, you need to pull out and then disassemble the head. It usually includes a shroud, spring (on some models), a bobbin with a fishing line, a cover. It is necessary to unplug the electric grass trimmer (or shut off the gasoline one), and then proceed to remove the spool. It can be fixed in two different ways: in the first case, you need to completely disassemble the head, and in the second. just remove it from the gearbox shaft, to which it is attached.

find the locks on both sides, press and remove the cover to open the inside of the head;

under the cover is the bobbin, it must be carefully pulled out of the housing (sometimes a spring is hidden under it, it should also be carefully put aside so as not to lose it);

• after removing the bobbin, a fixing bolt (or screw) becomes visible in the center of the housing, which must be unscrewed in the opposite direction to the clockwise movement;
• after removing the fasteners, it is necessary to hold by the body and with a rocking motion remove the spool from the gearbox shaft.

The second way is as follows. The reel head is mounted on the gearbox shaft. To disconnect it, you need to lock this shaft. Usually a hole is made in the mowers, e.g. Champion or STIHL, into which a nail, rod or screwdriver can be inserted. After locking the shaft in a stationary position, hold the housing and begin turning the head clockwise, since the threads on the shaft are usually applied to the left.

Now that the head is removed and disassembled, you need to determine how thick the cord should be. Learn the correct diameter for your trimmer for the grass can be found by looking in the user manual or on the bobbin itself, it usually shows similar information. Another way is to insert the filament into the hole from which it is fed. If the line goes without difficulty, it can be used for work.

How the line head works on the brushcutter why you need to know the principle of operation

Depending on the manufacturer, they not only differ externally, but also internally. Most reels have a pressure spring inside (semi-automatic and automatic). Above is an instruction on how to disassemble the grass trimmer head without a spring, t.е. on the head of the manual type. The principle of disassembling a semi-automatic head with a spring inside is almost identical to the above instruction.

The principle of the semi-automatic grass trimmer reel is as follows:

• Inside the head there is a spool, which is seated on slits that prevent it from moving freely
• The spool is actuated by a spring, which presses it to the slits in the cover structure
• There is a line wound on the lead for the trimmer, the length of which depends on the tool itself. Usually this length is 1 to 4 meters
• When working to increase the length of the line, the protruding part of the reel is pressed down, so that it is disengaged from the splines. At the same time, the line for the trimmer is reeled off the reel, increasing in length
• After releasing the necessary amount of line, release the clamp and continue mowing the grass

The advantage of a tool with a fishing line is that this consumable does not require sharpening, compared to metal discs. In addition, if a stone or wood gets in the way, the line for the trimmer simply comes off, without negatively affecting the gearbox and engine of the tool, as it happens in the case of metal cutting discs.

READ Interskol Grass Trimmer Warms And Stops

Knowing the construction and design of the types of mowing or trimmer heads, it is necessary to go on to consider the process of threading the line into the grass trimmer reel. After all, this is the point at which most owners of special tools causes difficulties.

How the head with a fishing line on a brushcutter works Why it is necessary to know the principle of work

Depending on the manufacturer, the heads differ structurally not only externally, but also internally. Most reels have a compression spring inside (semi-automatic and automatic). Above is an instruction on how to disassemble the grass trimmer head without the spring, t.е. On the head of the manual type. The principle of dismantling a semi-automatic head with a spring inside is almost identical to the above instruction.

The principle of the semi-automatic grass trimmer reel is as follows:

• Inside the head there is a spool, which is seated on slits preventing its free movement
• On the spool acts spring, which presses it to the slits in the design of the cover
• A line for the trimmer is wound on the guide, the length of which depends on the tool itself. Usually this length is between 1 and 4 meters
• During work, when the line length needs to be increased, the protruding part of the reel is pressed, by which it is disengaged from the slots. The filament for the trimmer is coiled from the drum, increasing in length
• After releasing the desired amount of line, release the clamp, and continue mowing

The advantage of a tool with a fishing line is that this consumable does not require sharpening, in comparison with metal discs. In addition, if a stone or wood gets in the way, the line for the trimmer simply comes off, without negatively affecting the tool’s gearbox and engine, as is the case with metal cutting discs.

READ Interskol Grass Trimmer Warms And Stops

Knowing the construction and design of the types of mowing or trimmer heads, it is necessary to proceed to consider the process of threading the line into the grass trimmer reel. Because this is what most power tool owners have trouble with.

What do you think of the Patriot pt 555?

Since I have a lot to compare it to, I’ll be blunt. Difference in engines 1.3 horsepower and 3 horsepower. Only when there’s something to cut.

It makes no sense to buy a powerful machine if you have a signature lawn planted on the site. One awkward move and a trimmer blade will shave that kind of grass to a bald spot on the ground. But if you’ve come to an abandoned virgin land Or you just need to mow a hectare or two, the Patriot gasoline trimmer shows what a sure way to mow through small growth.

There was a bush in the way? No problem, install the saw blade and in a few minutes cut just above the ground level. Spruce, birch, willow. enough power to cut down even small trees. Just don’t get carried away. Remember, this isn’t a Druzhba chainsaw