the grass trimmer stalls when the choke is opened

2-Stroke Engine Only Runs on Choke (Will Not Run) Why?

The lawn mower stalls when you press the gas, how to fix a breakdown

Likewise, when the throttle is pressed, the tool stalls because the drive is clogged. The following option is also possible: the fuel is not supplied in full, so you need to check or replace the fuel filter. Other possible reasons for a stalled brushcutter when you give gas are:

• Crankshaft oil seals suck in air;
• A spacer that is located between the carburetor and the cylinder in a “problem” situation;

To all these reasons for which the mechanism stalls when gas is added, we will add some useful recommendations for handling the brushcutter. First of all, before starting work with any technique, you need to read the instructions. In this case, the consistency of gasoline and oil plays an important role, it is competently prepared by you, and also not to overheat the unit, and not to leave gasoline for the winter when you simply will not use the car.

The well-coordinated work of all its components plays an important role in the full-fledged work of any tool. And if in one it is a line for a brushcutter, then in the other there is a piston or a carburetor. Owners of brushcutters who want to use their tool at full capacity need to understand that under a load for which the capabilities of the machine are not designed, the entire mechanism or its individual parts can simply break. Therefore, only competent and moderate operation presupposes long-term efficient operation of any gasoline-powered tool.

Causes of malfunction and their elimination

To most accurately determine the cause of a malfunction of any brand of grass trimmer (for example, Echo) and find out the possibility of its elimination, it is necessary to establish at what action the device stalls. The engine can be turned off both at idle and at high speeds, heating up under load or immediately after starting, etc.

If it stalled when opening the damper

If the equipment works properly at idle, but stalls when the air damper is opened, this indicates the penetration of air into the system through cracks in the fuel supply hose or damaged oil seals. In order to fix the breakage and adjust the operation of the tool without sucking air from the atmosphere, it is necessary to replace the damaged parts.

Another possible cause of a breakdown is a malfunction of the carburetor dosage system. To fix this problem, it is better to contact the professionals.

If stalled at high speeds

If the carburetor stalls at high speeds, this means that at idle and low speeds, the incoming fuel is enough for it, but not enough to work at high speeds. Then it is necessary to check the serviceability of the following units of the grass trimmer.

• Fuel hose. may have been damaged by cracking. In this case, you need to replace the part. Or maybe you just need to tighten the clamps.
• The filter mesh between the carburetor and the gasoline supply hose. it could be clogged. In this situation, it is necessary to clean the part.
• The valve located on the gas tank cap. it could get stuck or clogged with debris. Cleaning is also needed.
• Carburetor. it may be misaligned as a result of constant vibration. This is usually the case for cheap Chinese parts. To fix the problem, you need to configure according to the instructions. In some cases, it is enough just to loosen the tightening of the carburetor body. If the adjustment fails, you need to install a new element.
• Additionally, you should check the air filter. It may need to be rinsed and cleaned or replaced with a new one, as it could become clogged with dirt and grass particles when the equipment is tilted, when the user mowed in hard-to-reach places.

the lawn mower stalls when you press the gas cause

Those who have lawns on their backyard know that a grass trimmer is quite a useful thing that will help you quickly and efficiently tidy the lawn or clear weeds from overgrown areas. And, like any mechanism, it also often fails due to various breakdowns. One of the most common complaints from appliance owners is that the grass trimmer stalls when you press the gas. We propose to understand the main reasons for this phenomenon and identify ways to solve the problem.

If stalled after gas supply

Owners of gasoline braids quite often mention that the lawn mower stalls when you press the gas. Typically, such a breakdown occurs due to a malfunction in the carburetor. Failure in its operation can occur due to prolonged storage, use in difficult conditions, significant overload of the motor. Vibrating movements of the device during operation will become a symptom of such a breakdown.

On a note! Users familiar with car carburetor repair can try rebuilding this important grass trimmer unit on their own using the instruction manual. Otherwise, the right decision would be to contact the service center representatives for help.

Sometimes the grass trimmer stalls when you throttle because the fuel valve is clogged. This interferes with the supply of gasoline. To fix the problem, it is enough to loosen the valves. This will restore the normal fuel supply to the carburetor.

Another possible reason the mower stalls when gas is applied is a dirty breather (check valve). This part prevents the formation of a vacuum in the gas tank. If it is clogged, air does not flow, which means that fuel does not go to the carburetor. To fix the problem, you need to clean this element.

If stalled without gaining momentum

If the grass trimmer does not pick up and shuts down, there could be several reasons. The most common culprit is a clogged air filter. It must be pulled out and cleaned, if necessary, replaced.

On a note! The grass trimmer could stall without gaining speed due to a carburetor malfunction. The unit for repair or replacement must be taken to the service center.

Another possible malfunction is related to the mechanics of the motor drive. This part of the grass trimmer must be thoroughly cleaned and the inner cables must be lubricated.

You also need to make sure that the cable in the carburetor has not slept. Before using the grass trimmer for the first time, check this structural element to ensure that it is firmly and not taut. Otherwise, the cable may crack, resulting in costly repairs.

Immediately after wound up

The unit may stall immediately after starting if the carburetor is misaligned or incorrectly adjusted. this causes an uneven fuel supply. The result is that the device vibrates distinctly. To troubleshoot the carburetor, readjust, following the instructions for the mechanism.

Also, the engine stops when the fuel supply valve becomes clogged. In such cases, it is sufficient to simply clean it. If the mower started up at first, but then immediately stalled, then it is possible that the fuel enters the carburetor unit with some difficulty. The weakening of the valve helps to resolve the issue, which ensures free circulation of the mixture in the system.

A stop can also be caused by air leaks in the presence of mechanical damage to the hose (holes, cracks) that takes the fuel. In this case, add more revolutions to the drive in order to quickly expel air bubbles from the system.

Why the petrol grass trimmer stalls

A petrol-powered grass scythe is a useful thing for owners of home gardens, lawns, and when the grass trimmer suddenly stalls, the work to clear the area of ​​grass stops. The device itself is a rather complex mechanism, so there are many different reasons for its breakdowns. The most common malfunctions are contained in the operating instructions. Knowing the reasons why the grass trimmer stalls should be done in order to effectively repair the device yourself.

At high revs

When the scythe for grass stalls at high speeds, this is due to the following problems:

• clogging or sticking of the valve located on the gas tank cap;
• the carburetor is out of alignment under the influence of vibrations arising from the operation of the mechanism;
• problems with the circulation of the fuel mixture;
• suction of atmospheric air;
• the fuel intake hose is cracked or loose.

Adjust the carburetor referring to the trimmer operating instructions. For adjustment, it is often sufficient to loosen the tightening of its housing. If there are problematic points with the circulation of the fuel mixture, then it can gradually enter the carburetor. After its development, the engine stalls at high speeds.

When you press the gas

If the mower stops when you press the gas, the reasons may be as follows:.

• The most common option is carburetor adjustment failure, which occurs when the drive is under significant stress, after prolonged inactivity of the mechanism, or when it is used in difficult conditions.
• Clogging of the fuel valve, which is eliminated by loosening it, as a result of which gasoline begins to flow normally through the system.
• Loosening and drooping of the cable in the carburetor. The fuel hose may also be stretched to the point of rupture due to significant stress.
• Clogged breather (non-return valve), as a result of which fuel does not flow into the tank.

If the problem is with the carburetor assembly, the mower vibrates to recognize it. When the hose bursts or the cable is stretched, these components are replaced.

Small Engine Won’t Run Without Choke. RustySkull Productions

What could have broken

Problems with the petrol brush, due to the fact that this device does not start, are classified in a certain way by service specialists. They highlight faults with the following components of the mechanism:

• an engine in which the piston and bearings may wear out or fail, crack the crankcase;
• the fuel supply system, while the filter may be clogged or problems with the carburetor;
• mechanical damage to wires, tubes, hoses;
• ignition circuit.

To correctly identify the node where the breakage occurred, you need to pay attention to the circumstances under which the grass trimmer stalls.

Idle

At idle, common reasons for stopping the grass trimmer are as follows:

• contamination, misalignment or incorrectly adjusted carburetor adjustment;
• clogged air filter;

• reducing the speed of the gearbox when it heats up, which is a consequence of using an unsuitable fuel mixture;
• clogged throttle;

• air ingress into the system;
• not enough fuel to operate the lawn mower.

If the problem area is the carburetor, then the equipment will stop at both “cold” and “hot” start.

When heated

the lawnmower often stops when it heats up. At the same time, it starts up, works “jerky” and gradually stops. This process occurs when the gasoline in the carburetor boils or the damper is installed in a rotary rather than disc type. In the latter case, the part is changed.

It happens that the grass trimmer heats up if the ignition wire or coil is damaged. Parts are replaced in order for the device to start working normally.

When the air damper is opened

It happens that the unit stalls when the air damper is opened, normally idling. This is due to air leaks in the system, caused by cracks in the fuel hose or problems with the oil seals. The carburetor metering system may also malfunction, and the mower will stop after opening the damper.

All possible reasons that the lawn mower stalls, and how to fix them, are contained in the following video.

There are many reasons for stopping the brushcutter, but the most common malfunctions associated with its carburetor. They can arise in any case. The most problematic option is when a serious breakdown occurs, and you need to purchase new parts or change the lawn mower.

In order for the grass trimmer to work properly for a long time, you must strictly follow the instructions for use. It is necessary to fill the unit with a suitable fuel mixture, the unit should operate at moderate load.

When you press the gas

If the mower stops when you press the gas, the reasons may be as follows:.

• The most common option is carburetor adjustment failure, which occurs when the drive is under significant stress, after prolonged inactivity of the mechanism, or when it is used in difficult conditions.
• Clogging of the fuel valve, which is eliminated by loosening it, as a result of which gasoline begins to flow normally through the system.
• Loosening and drooping of the cable in the carburetor. The fuel hose may also be stretched to the point of rupture due to significant stress.
• Clogged breather (non-return valve), as a result of which fuel does not flow into the tank.

If the problem is with the carburetor assembly, the mower vibrates to recognize it. When the hose bursts or the cable is stretched, these components are replaced.

Why a lawn mower stalls: troubleshooting methods

Why does the grass trimmer stall when I press the gas? Reasons for stopping the grass trimmer at high and idle rpm, heating or opening the air damper. What to do if the petrol grass trimmer starts up and stalls right away?

• What could have broken
• Specifications STIHL FS38
• When you press the gas
• The second is the carburetor
• Diesel stalls at idle
• the lawn mower stalls on hot? There is a solution!
• When heated
• Restoration of electrical equipment
• Overview
• Operating tips
• the grass trimmer starts up and stalls immediately
• grass trimmer does not idle
• When you press the gas
• Model Description
• The best trimmer models according to buyers in 2018
• complex causes of lawn mower failure

the lawn mower stalls on hot? There is a solution!

the mower stalls when hot. this means that there is already some fuel in the engine to start the engine, but after 5-10 minutes of operation, it stops working. This behavior of the engine indicates problems with the fuel filter.

There are two solutions. preventive and radical. Preventive is to try to clean it, which will consist in cleaning the contamination with a solvent, and then blowing the filter with a jet of compressed air.

But in case of severe pollution, you can fix the breakdown only by applying a radical solution. this is the purchase of a new fuel filter.

Overview

The Motokosa STIHL FS38 belongs to the lighting group and is the perfect complement to the powerful lawnmower for recording inaccessible areas along paths, under trees and bushes. With STIHL mobile lawnmowers, you can quickly mow soft, overgrown lawns and lawns, always keeping a small area clean.

When you press the gas

If, when you press the gas, the gasoline cutter stops, then the reasons may be as follows.

• The most common option is a malfunction of the carburetor adjustment, which occurs when the reins are under heavy load, after prolonged inactivity of the mechanism or when using it in difficult conditions.

If the problem is with the carburettor block, it can be recognized by the vibration of the gasoline cutter. When a hose bursts or a cable stretches, these components are replaced.

When heated

the lawnmower often stops when it heats up. At the same time, it starts up, works “jerky” and gradually stops. This process occurs when the gasoline in the carburetor boils or the damper is installed in a rotary rather than disc type. In the latter case, the part is changed.

It happens that the grass trimmer heats up if the ignition wire or coil is damaged. Parts are replaced in order for the device to start working normally.

At high revs

When the scythe for grass stalls at high speeds, this is due to the following problems:

• clogging or sticking of the valve located on the gas tank cap;
• the carburetor is out of alignment under the influence of vibrations arising from the operation of the mechanism;
• circulation problems fuel mixture;
• suction of atmospheric air;
• the fuel intake hose is cracked or loose.

Adjust the carburetor referring to the trimmer operating instructions. For adjustment, it is often sufficient to loosen the tightening of its housing. If there are problematic points with the circulation of the fuel mixture, then it can gradually enter the carburetor. After its development, the engine stalls at high speeds.

Eliminating Reasons Your Lawn Mower Won’t Start

The fuel mixture must be prepared with the exact proportions of gasoline and oil. In this case, you cannot use another brand of fuel. To exclude the ingress of dirt, gasoline must settle in glass or metal containers for 2 days. Do not use plastic utensils for storing fuel. Measure the oil accurately with a medical syringe without a needle. Use only freshly prepared mixture, do not leave unused fuel in the tank. If the engine is naughty, the lawn mower stalls, when you press the gas, the fuel may be to blame.

Website about the cottage

grass trimmer STALLS carburetor adjustment.

For even more information about repair and tool selection on our website www.LookTool.Ru visit we are glad to everyone

08.12.2018 admin Комментарии и мнения владельцев No Комментарии и мнения владельцев

Why does the grass trimmer stall when I press the gas? Prerequisites for stopping the grass trimmer at high and idle speeds, when heating or opening the air damper. What to do if the petrol grass trimmer starts and stalls right there?

A grass scythe with a gasoline drive is a necessary thing for owners of personal plots, lawns, and when the grass trimmer stalls at one moment, the work on cleaning the area from grass stops. The device itself is a rather complicated mechanism, therefore there are many different circumstances of its breakdowns. often arising problems are contained in the operation annotation. To know the prerequisites why the grass trimmer stalls, it follows that without the help of others, it is perfectly possible to repair the device.

Why does a lawn mower stall under load?

How not to get confused if your lawnmower won’t start

The tool, despite its small size, is a complex technical device. If you study the annotation for operation, it turns out that the prerequisites for why the lawn mower does not start are known and removable. It is necessary to eliminate one by one the reasons that make it difficult to start the tool. Why does the grass trimmer stall when pressed at high rpms. the lawn mower stalls. Usually start with more accessible nodes with an easy health check.