STIHL 180 does not start well when hot

Broken fuel line

During the operation of the chainsaw, vibration occurs, which can cause damage or breakage of the fuel line of the chainsaw. In this case, the chainsaw will stall and it will be impossible to start. To diagnose a malfunction, you need to conduct an inspection and determine the presence of fuel leaks.

STIHL 180 does not start well for hot reasons.

Chainsaw breakdowns often occur due to insufficient chain lubrication due to oil line leakage and clogged channels. Therefore, if the chain becomes dry, it is necessary to urgently clean the channels supplying oil to the tire. Then an inspection of the joints of the pipes with the oil pump fittings is carried out. If a strong leakage of oil from the points of contact or cracks in the oil line is detected, the pipes are changed, and the joints are sealed with a high-quality sealant.

Some parts of chainsaws must be changed after the expiration of the passport service life. Therefore, do not forget to look at the instructions, where they are clearly spelled out. Such parts include the tire, the drive sprocket, the chain, parts of the anti-vibration system.

If the replacement is not done on time, the wear of these components will negatively affect the serviceable parts of the chainsaw. For example, a long delay in replacing a drive sprocket results in increased vibration, which quickly breaks down the crankshaft bearings.

Therefore, it is necessary to regularly check the working depth of the teeth, which should not exceed 0.5 mm. The tire resource is usually enough for 3-4 chains, after which it also needs to be replaced.

Useful video on the correct operation of the chainsaw:

Engine jammed

Quite often there is a situation when the saw worked and stalled abruptly, the cause of which was the engine jamming, which in turn occurred as a result of a broken piston skirt, destruction of the crankshaft bearing, protrusion of the piston pin cork ring or piston ring fracture.

Stihl FS 94 R. Hot Start Problems

stihl, does, start

A jammed engine can be easily identified by pulling on the starter cord. In the case when the starter does not turn, most likely, it has jammed, and further repairs are possible only at the service center.

The gap between the ignition coil and the flywheel

An incorrectly set gap between the flywheel and the contacts of the ignition coil affects the quality of sparking, which in turn is responsible for normal start-up and stable operation of the engine.

Malfunctions in the ignition system

If, when inspecting the spark plug, it is found that it is wet and sparking on the contacts does not occur, this means that the problem should be looked for in the ignition system, inspect the coil, check the gap between the flywheel and the coil contacts. You can also check how tightly the cap of the high-voltage wire sits on the candle, and the candle itself. Try to replace it with a new one.

Other malfunctions

  • For many owners, the question regarding the correct idle speed after emptying the fuel from the gasoline tanks is relevant for many owners. According to experts, there is no need to worry too much about this. However, if you have to deal with a similar problem often, then it is enough to manipulate the carburetor by reducing the engine speed in order to restore the normal operation of the tool.
  • In some cases, the owner may need to clean the muffler as this part may be causing the malfunction. This operation is quite simple. It must be remembered that many owners are faced with problematic chainsaw operation due to a faulty carburetor.
  • Although in some cases it may be quite simple to troubleshoot a malfunction, it is most preferable if specialists will repair this equipment. After all, not each of us has the necessary knowledge and skills, and this is fraught with the fact that during self-troubleshooting there is a risk of completely disabling the tool.

Spark plug

The spark plug is one of the main elements of the ignition system. A spark is formed on its electrodes, and if this element fails, it will be difficult to start, or it is not possible at all.

The plug can fail completely, or work intermittently or give out a weak spark. It is quite simple to check the spark plug, for this you need to unscrew it from the engine, attach it to the high-voltage wire cap and, putting it on the cylinder, pull the starter. If the candle is in order, the spark will be powerful with a bluish tinge. A faint reddish spark is a sign of a problem. Defective spark plug must be replaced.

Summing up

In fact, as you can see, there are a lot of reasons for the breakdown of the STIHL 180 chainsaw, and at the same time, there are also many solutions to this problem. If you are faced with this situation, then simply follow all the above recommendations and then, undoubtedly, you can repair your device, and it will delight you with its work for many years to come.

Algorithm for checking for lack of fuel supply

  • Unscrew the candle;
  • Using a syringe, pour 1-2 cubes of the fuel mixture into the spark plug hole;
  • Install the candle and put on the cap of the high-voltage wire;
  • Set the engine control lever to the hot start position;
  • Pull the starter several times.

If, after several movements with the starter, the STIHL 180 chainsaw started up and immediately stalled, then the suspicions in the lack of fuel supply were confirmed and you can proceed to further diagnostics of the fuel line.

Replacing the crankshaft bearings

It is better to replace the crankshaft bearings in a specialized service, since when replacing, you will need to completely disassemble the STIHL 180 chainsaw and remove all its main components.

Without some experience or at least the skills of repairing similar chainsaws, it will not work to replace the crankshaft bearings efficiently.

So, we figured out the lack of a spark, but what to do if there is a spark, and there is no answer to the question of why the STIHL 180 chainsaw does not start. The reason may be hiding in the fuel system.

There is no spark on the STIHL 180 chainsaw

The main malfunction due to which the STIHL ms 180 chainsaw does not start may be the absence of a spark between the electrodes on the spark plug. Signs of this malfunction can be detected by unscrewing the spark plug and inspecting it. Having discovered during inspection that the spark plug is wet, it is necessary to start looking for the reason for the absence of a spark on the spark plug.

Why Small Engine Shuts off and Doesn’t Start Until Its Cool

For what reasons the STIHL MS 180 chainsaw will not start

The STIHL MS 180 chainsaw is considered one of the most reliable tools for gardening. But with any technique, there are situations when for some reason it does not start. Let’s take a look at the main faults due to which the STIHL 180 will not start or start poorly and how to fix these faults.

Other malfunctions

  • For many owners, the question regarding the correct idle speed after emptying the fuel from the gasoline tanks is relevant for many owners. According to experts, there is no need to worry too much about this. However, if you have to deal with a similar problem often, then it is enough to manipulate the carburetor by reducing the engine speed in order to restore the normal operation of the tool.
  • In some cases, the owner may need to clean the muffler as this part may be causing the malfunction. This operation is quite simple. It must be remembered that many owners are faced with problematic chainsaw operation due to a faulty carburetor.
  • Although in some cases it may be quite simple to troubleshoot a malfunction, it is most preferable if specialists will repair this equipment. After all, not each of us has the necessary knowledge and skills, and this is fraught with the fact that during self-troubleshooting there is a risk of completely disabling the tool.

STIHL 180 chainsaw won’t start: main reasons

Today, many manufacturers are engaged in the production of units for agricultural and construction work, among which the most demanded is the equipment manufactured by STIHL. The high level of quality is not the only reason why the products of this manufacturer are popular in the market. This was also facilitated by the democratic price and optimal power that the models of this brand have.

It seems that many had to use a chainsaw of a similar brand. over, it is not easy to use, but regularly perform a wide variety of work and make sure of the high performance characteristics of this tool. Such a proliferation of these products is no coincidence, given that, in addition to power, this instrument stands out for its graceful design. However, one must remember that this is still a technique for which the resource of work is limited. Therefore, each owner of such a unit at some point is faced with the need for repair. Next, we will talk about the features of repairing the STIHL 180 chainsaw.

Common isues with Stihl MS 170 and MS 180 Chainsaws